Használati útmutató CyberPower CPS240PAU

CyberPower Accu CPS240PAU

Olvassa el alább 📖 a magyar nyelvű használati útmutatót CyberPower CPS240PAU (2 oldal) a Accu kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

YOUR ULTIMATE ALLY IN POWER FEATURES SPECIFICATIONS

1. 120V AC outlet Model Number: CPS240PAU

POWERTRIPTM 240

AC MOBILE POWER INVERTER

CPS240PAU

USER MANUAL

2. USB Charging Port

3. LED Indicator Light

Power LED (Green), Input / Output Fault (Red)

4. ON/OFF Switch

5. DC Input Positive Terminal

6. DC Input Negative Terminal

7. Cooling Fan

Input Voltage:

Output Peak Power:

Output Continuous Power:

Output Voltage:

Output USB Voltage:

Output Frequency:

Output Waveform:

Input Fuse (internal):

Input Fuse (cigar plug);

11 to 15 V

240 W

200 W

120 V

5 V

60 Hz

Simulated Sine Wave

25 A

15 A

Protection Features: Overload, Overvoltage,

Overheating, Short-circuit

iWARNING: This product can expose you to chemicals including bisphenol A

(BPA) and styrene (ABS), which is known to the State of California to cause

reproductive harm and cancer. For more information, go to www.P65Warnings.

ca.gov.

IMPORTANT SAFETY WARNINGS

This guide contains important information regarding the safety, operation, maintenance, and storage of this product.

Failure to read this guide and follow the directions could result in injury and/or property damage.

Before installing and using the CyberPower power inverter, please read the manual. Misusing or incorrectly connecting the

Inverter may damage the equipment or create hazardous conditions for users. Read the 8 following safety instructions and

pay special attention to all CAUTION and WARNING statements in the manual.

CAUTION! Do not operate the inverter near ﬂammable CAUTION! Always turn the inverter o when not in use by

materials, fumes, or gases. removing it from the DC accessory port.

CAUTION! Always use the inverter where there is adequate Check the warning labels on battery chargers CAUTION!

ventilation. Do not obstruct the ventilation slots. or adapters before connecting them to the inverter. Do not

connect battery chargers or adapters that have warnings

CAUTION! Never immerse the unit in water or other liquids. about using with inverters.

CAUTION! Proper cooling is essential when operating the

inverter. Refrain from placing the inverter near the vehicle’s

heat vent or in direct sunlight.

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379

CyberPowerSystems.com

DC FUSE REPLACEMENT BASIC OPERATION - Loads Under 150W BASIC OPERATION - Loads Over 150W

The CPS480TG2U/B inverter contains protection fuses.

Two on the inverter body and the other on the cigar plug

cable to protect the unit against overloading. If the inverter

draws more than 150 watts via the cigar plug connection,

or more than 480 watts via the battery clamp connection,

the internal fuse may open to protect the inverter, vehicle

battery, and the connected equipment.

To replace the fuse, please followthe instructions below:

1. Turn o the inverter and disconnect any devices from

the inverter.

2. Disconnect the inverter from power source and remove

the leads.

3. Pull the fuse straight out of the holder.

4. Replace with a new 25-amp fuse in the inverter body or a

20-amp fuse located inline on the cigar plug cable.

Spring

Ring

Power plug

15A Fuse

TROUBLESHOOTING

Problem Possible Cause

DC input is below

11 Vdc or over 15 Vdc

Short Circuit

No AC output

Red LED lit

Overload

Inverter hot

Bad connection or

No AC output wiring

Green LED

not lit Fuse is blown

Excessive startup

load. If the start up

Motorized load exceeds the

power tool will inverter’s peak load

not operate. capability it will

not work.

Contact Pin

Contact Retainer

Solution

Check your battery volts and

recharge or replace the battery.

Disconnect the load.

Reduce the load.

Disconnect the load and operate

the inverter for a few minutes.

Tighten all DC connections

Check fuse and replace or call

service.

Disconnect the load until the

inverter operates normally and

connect the load again.

1. Place the inverter on a

ﬂat surface on your

vehicle ﬂoor.

2. Make sure the power switch

on the panel is o.

3. Take the power cord

equipped with the cigar

plug and place the ring

terminals over the two

cabling terminals on the

back of the inverter.

4. Place the inverter cigar

plug in the vehicle cigarette

lighter socket.

CAUTION

1. Connect the RED cable to

the POSITIVE terminal of

the inverter.

2. Connect the BLACK cable

to the NEGATIVE terminal

of the inverter.

5. Turn on the power switch. The green light indicates that the

inverter is operating normally and that AC power is available

at the outlet.

6. Verify that the connected device(s) draws less than 150

watts and plug into the AC outlet.

7. Always turn the inverter o when not in use.

CAUTION - Make sure you connect cable red to red and black to black, and make

sure you screw the nuts on tightly.

CAUTION - Use the cigar plug cable only when the vehicle’s engine is running.

CAUTION - Use the cigar plug cable with the engine o will cause excessive

TM480 User Guide battery drain.

OPERATING AND STORAGE TIPS

The inverter should only be operated under the

following conditions:

• Dry - Do not allow water or other liquids to come into

contact with the inverter.

• Moderate Temperature - Ambient air temperature should

be between 32 °F - 104 °F (0 °C - 40 °C). Keep the

inverter out of direct sunlight.

• Free Air Flow - Keep the inverter’s ventilation slots

unobstructed to ensure air ﬂow to the unit.

FOR MORE INFORMATION

Visit CyberPowerSystems.com for more information regarding:

• Product information and certiﬁcations

• Product warranty

• Connected equipment guarantee

1. Place the inverter on a

ﬂat surface.

2. Make sure the power switch

on the panel is o.

3. Take the power cord equipped

with battery clamps on one end

and place the ring terminals over

the two cabling terminals on the

back of the inverter.

4. Fasten the positive (red)

clamp to the positive battery

post, and thenfasten the negative

(black) clamp to the negative

battery post.

5. Turn on the power switch. The

CAUTION

1. Connect the RED

cable to the POSITIVE

terminal of the battery.

2. Connect the BLACK

cable to the NEGATIVE

terminal of the battery.

green light indicates that the inverter is operating

normally and that AC power is available at the outlet.

6. Take device power cord plug into the inverter

AC outlet.

7. Always turn the inverter o when not in use.

CAUTION - A reverse polarity connection (positive to negative) will blow a fuse

in the inverter and may permanently damage the unit. Damage caused by a

reverse polarity connection is not covered by your warranty.

WARNING - Batteries contain corrosive materials and present an electrical shock

hazard. To prevent irritation and burns, wear protective eyewear and clothing

when you install the inverter or work with the batteries. Take special care to en-

sure that metal tools and personal metal objects like rings and bracelets do not

contact the battery terminals.

• Do not place any items on or over the inverter during

operation. The unit will shut down if it overheats.

• Proper storage temperature range is

32 °F - 122 °F (0 °C - 50 °C).

• Store and use the inverter in a cool and dry environment.

• Avoid exposing the inverter to heating elements, direct

sunlight, or high humidity.

TECHNICAL SUPPORT

Visit: CyberPowerSystems.com/support

Toll-Free: 1-877-297-6937

Hours of Operation: Monday - Friday: 7:00am - 6:00pm CST

All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS equipment generates, uses, and can radiate radio frequency ener- • Reorient or relocate the receiving antenna.

This device complies with Part 15 of the FCC Rules. gy and, if not installed and used in accordance with the instruc- • Increase the separation between the equipment and receiver.

Operation is subject to the following two conditions: tions, may cause harmful interference to radio communications. • Connect the equipment into an outlet on a circuit dierent

(1) this device may not cause harmful interference, and (2) this However, there is no guarantee that interference will not occur from that to which the receiver is connected.

device must accept any interference received, including interfer- in a particular installation. If this equipment does cause harmful • Consult the dealer or an experienced radio/TV technician

ence that may cause undesired operation. interference to radio or television reception, which can be for help.

This equipment has been tested and found to comply with the determined by turning the equipment o and on, the user is

limits for a Class B digital device, pursuant to Part 15 of the FCC encouraged to try to correct the interference by one or more of WARNING: Changes or modiﬁcations not expressly approved

Rules. These limits are designed to provide reasonable protection the following measures: by the party responsible for compliance could void the user’s

against harmful interference in a residential installation. This authority to operate the equipment.