Használati útmutató Erica Synths Fusion VCO
Erica Synths
nincs kategorizálva
Fusion VCO
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Erica Synths Fusion VCO (6 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 4.5 felhasználó értékelte átlagosan 5.0 csillagra
Oldal 1/6
ERICA FUSION VCO
S
U
B
W
A
V
E
1
S
U
B
M
I
X
C
O
L
O
U
R
S
U
B
W
A
V
E
2
F
R
E
Q
U
E
N
C
Y
W
A
V
E
S
H
A
P
E
F
M
L
E
V
E
L
AUDIO IN 1V/OCTSUBMIX CV FM IN WAVE CV VCO OUT MIX OUT
-2-1
D
R
Y
/
W
E
T
FUSION VCO
THANK YOU FOR ORDERING
ERICA FUSION VCO MODULE!
The Erica Synths Fusion series modules
are designed combining vacuum
tubes and semiconductors therefore
they bring warm, powerful sound and
overdrive possibilities of vacuum tubes
into your modular system. Erica Fusion
series consist of range of modules
used in sound shaping circuit – VCO,
Mixer, real Ringmodulator using
audio transformers and germanium
diode ring, VCF, VCA and Analogue
Delay/Chorus.
Conventional wisdom says that
vacuum tubes have nonlinear
characteristics, and therefore VCOs
based on vacuum tubes need special
tuning for each note.
Erica Synths Fusion VCO is special
kind of VCO – it fuses good tuning
of digital VCO with warm, unique
sound of vacuum tubes that work in
suboscillator circuit. The module has to
vacuum tube based suboscillators: -1
and -2 octaves with plenty of mixing
opportunities for amazing sonic results.
If you wish to go really low frequencies
and have a sound that sets your
modular system apart from mass –
this is exactly module, you need!
FEATURES:
3 basic waveforms with VC morphing
Good 1V/oct tuning
Vacuum tube based suboscillators -1 and -2 oct
Manually and CV controlled -1/-2 oct mixing
Adjustable suboscillator waveshape
Dry/Wet (VCO/suboscillators) mixing
Passive Lowpass filter for extreme subbass sound
Audio input
TECHNICAL SPECIFICATIONS:
Audio input level: up to 20V ptp .....................................................................................................
VCO range: C1 – C8 .........................................................................................................................
Max Output level: 10V ptp ...............................................................................................................
Panel width: ............................................................................................................................ 24HP
Module depth: 35mm .....................................................................................................................
Power supply: bipolar +-12V , eurorack standard and/or Erica Synths 6VAC PSU .................
Power consumption:
Tube heater PSU configuration: 60mA@+12V, 30mA@-12V, 300mA@6VAC ..........................
Eurorack PSU configuration: ..........................................................215mA@+12V, 185mA@-12V
(NB – start-up power consumption for few seconds is +-250mA)
Choose one of principal
waveforms of VCO
Set the VCO frequency
manually
Dry/Wet potentiometer
provides smooth mix between
pure VCO and pure tube
suboscillator sound
Use COLOUR potentiometer
to filter o higher harmonics
for extreme bass sound and
almost pure sine waveform
on the output. Full CCW
setting works best at really
low frequencies –
C1 and below
Adjust -1 octave
suboscillator waverofm from
more harmonic rich CW to
almost sine CCW
Adjust a mix between
-1 octave and -2 octaves
suboscillators
Connect 1V/oct
signal to control
VCO frequency
Apply CV to fade
between -1oct
and -2oct mix
Patch
FM CV
here
Apply wave
morphing CV here.
It will be added
to waveshape
potentiometer
setting
This is dry VCO
output, no
suboscillator is
added
This is master output. Get
that fat tube sound here
Adjust -2 octave
suboscillator waverofm from
more harmonic rich CW to
almost sine CCW
Use waveshape
potentiometer to
morph/adjust waveforms.
12 ‘o’clock setting gives
you waveform, selected
by the switch, and then
morphing is applied:
• Sine morphs from
logarythmic wave to
overdriven sine
• Triangle morphs from
ramp to sawtooth
• Pule has adjustable PW –
from 5% to 95%
Patch external VCO (simple
waveforms will work best)
to route it to suboscillator
circuit. Internal VCO will be
automatically disconnected
Adjust FM level with this
potentiometer
Termékspecifikációk
| Márka: | Erica Synths |
| Kategória: | nincs kategorizálva |
| Modell: | Fusion VCO |
Szüksége van segítségre?
Ha segítségre van szüksége Erica Synths Fusion VCO, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Erica Synths
21 Augusztus 2024
19 Augusztus 2024
18 Augusztus 2024
17 Augusztus 2024
17 Augusztus 2024
16 Augusztus 2024
15 Augusztus 2024
14 Augusztus 2024
14 Augusztus 2024
14 Augusztus 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Dahua Technology
- nincs kategorizálva IOTAVX
- nincs kategorizálva Vankyo
- nincs kategorizálva Thermaltake
- nincs kategorizálva Duromax
- nincs kategorizálva I.safe Mobile
- nincs kategorizálva Nikon
- nincs kategorizálva Valore
- nincs kategorizálva TC Helicon
- nincs kategorizálva Microboards
- nincs kategorizálva Paradigm
- nincs kategorizálva BabyHome
- nincs kategorizálva Multibrackets
- nincs kategorizálva BaByliss
- nincs kategorizálva Lego
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025