Használati útmutató Extech DCP36
Extech
nincs kategorizálva
DCP36
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Extech DCP36 (10 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 5 felhasználó értékelte átlagosan 4.6 csillagra
Oldal 1/10
USER MANUAL
Model DCP36
80W Switching DC Power Supply
User Manual Translaons available at www.extech.com
2 DCP36- - _V1.2 /20en US 12
Introducon
Thank you for selecng the Extech DCP36 laboratory grade W Switching DC Power Supply. The 80
DCP36 is auto-ranging and oers a 0.5~36V and 0~5A output capability. Its maximum current
output at 36V is 2.2A (80W/36V). The maximum voltage output at 5A is 16V (80W/5A).
The voltage/current spectrum is greater than three convenonal power supplies of the same
power rang. Adjustable Upper Voltage/Current Limit features protect sensive devices from
wide output variaons. Three user presets allow for easy programming and recall of commonly
used output conguraons. Master/Slave capability for up to 30 units in parallel connecon. The
DCP is perfect fo benchwork, eld service and hobbyists. 36 r ,
The DCP36 is shipped with the following accessories: AC power cord, RJ11 cable, alligator clip test
leads, and an RJ11 terminator plug.
This power supply is shipped fully tested and calibrated and, with proper use, will provide years of
reliable service lease visit the Extech website for the latest user manual and for customer . P
support.
Safety
This manual contains importa informaon illustrang the safe and proper use of th power nt is
supply. Read the enre manual and carefully observe the markings and labels this unit and on on
the equipment to which it will be connected.
Failure to observe may cause injury to persons and damage to the power supply or the connected Warnings
equipment. Failure to observe Cauon statements may result in damage to connected equipment improper and
funconing of the power supply.
WARNINGS
1. Do not use this power supply near water.
2. Do not operate or touch this power supply with wet hands.
3. Do not open the casing of the power supply when it is connected to mains. AC
4. Refer all servicing, including fuse replacement, to qualied service personnel.
CAUTIONS
1. Use a grounded 3-terminal source. AC
2. This t is intended for indoor use only. uni
3. Do not operate or place this unit in a humid or dusty environment.
4. Do not expose this device to direct sunlight or place it near a source of heat.
5. Before plugging into the local AC mains, check the rang label at the ck of the unit. ba
6. Do not block any of the venlaon openings the unit. on
7. This unit must be used within the specified ratings; Continuous and excessive loading may cause damage to
the power supply.
8. The gauge size of input power cable must be at least 0. m75m 2 (18awg) and the total length of power
cable must not exceed 3m (10).
3 DCP36- - _V1.2 /20en US 12
Power Supply Descripon
Front and Back Descripons
1. Output Voltage Display
2. Output Current or Power Display
3. SLAVE-SHIFT-LOCK funcon indicators
4. Output ON-OFF buon and indicator
5. Output preset selecon buons and indicators
6. LOCK and Amp/Wa-meter buon
7. MENU and SHIFT buon
8. Power ON-OFF switch
9. Output terminal egave) (n
10. Output terminal (posive)
11. Current output justment ad
12. Voltage output adjustment
13. Constant Current indicator
14. Constant Voltage indicator
15. Remote Sensing (RS) terminals
16. Alternate output (O/P) terminals
17. 11 Master RJ jack
18. 11 Slave RJ jack
19. Earth Ground terminal
20. AC power jack
Note that there is an addional RJ11 jack on the back of the unit
labeled ‘Reserved’ that is unused in this model
Display Descripons
Constant Voltage mode (C.V. indicator)
The output voltage is kept constant at the set voltage. The
DCP36 remains in CV mode if the load current is lower than
the set current limit otherwise it will switch to CC mo , de.
Constant Current mode (C.C. indicator)
When the load is higher than the set current limit of the set
voltage in CV mode, the Constant Current mode is acve.
The output current is kept constant at the set current level
provided that the loading is suciently large to draw
current equal to or larger than the set current, otherwise it
will switch to the CV mode.
Termékspecifikációk
| Márka: | Extech |
| Kategória: | nincs kategorizálva |
| Modell: | DCP36 |
Szüksége van segítségre?
Ha segítségre van szüksége Extech DCP36, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Extech
10 Január 2025
28 Szeptember 2024
19 Szeptember 2024
13 Szeptember 2024
2 Szeptember 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
26 Augusztus 2024
26 Augusztus 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva IHealth
- nincs kategorizálva Adam Hall
- nincs kategorizálva Yamato
- nincs kategorizálva Radial Engineering
- nincs kategorizálva Chord
- nincs kategorizálva Eve Audio
- nincs kategorizálva Proteca
- nincs kategorizálva Horizon
- nincs kategorizálva Insteon
- nincs kategorizálva Pure 100
- nincs kategorizálva Lexicon
- nincs kategorizálva Inspire
- nincs kategorizálva Livn
- nincs kategorizálva BSS Audio
- nincs kategorizálva Moomin
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025