Használati útmutató Gossen Metrawatt SYSKON P1500
Gossen Metrawatt
nincs kategorizálva
SYSKON P1500
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Gossen Metrawatt SYSKON P1500 (72 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.6 csillagra
Oldal 1/72
Operating Instructions
SYSKONP500, P800, P1500, P3000 and P4500
Computer Controlled Laboratory Power Supplies
3-349-373-03
13/10.16
2 GMC-I Messtechnik GmbH
Contents Page
Contents Page
1 Initial Inspection – Warnings . . . . . . . . . . . . . . 3
2 Initial Start-Up – Dimensional Drawings . . . . . . 4
2.1
Dimensional Drawing SYSKON P500 / P800 / P1500 . . 4
2.2 Dimensional Drawing SYSKON P3000 / P4500 . . . 5
2.3 Preparing for Operation . . . . . . . . . . . . . . . . . . . . . . 6
2.3.1 Installing the Optional GPIB Interface Module . . . . . . . . . . . 6
2.3.2 Setup as Benchtop Device . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3.3 Installation to a 19'' Device Cabinet . . . . . . . . . . . . . . . . . . 6
2.3.4 Connection to the Mains . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3.5 Connecting Power Consumers . . . . . . . . . . . . . . . . . . . . . . 6
2.3.6 Connection to Computer Interfaces . . . . . . . . . . . . . . . . . . . 6
2.3.7 Driver update (USB device driver) . . . . . . . . . . . . . . . . . . . . 7
2.3.8 Connecting the Analog Interface . . . . . . . . . . . . . . . . . . . . . 7
2.4 Switching the Device On . . . . . . . . . . . . . . . . . . . . . 7
2.4.1 Table of Firmware Versions . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.2 Response after Power ON with Varying Line Voltage
Ranges (230 V 115 V) . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Technical Description . . . . . . . . . . . . . . . . . . . .9
4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1.1 Electromagnetic Compatibility . . . . . . . . . . . . . . . . . . . . . 13
4.1.2 Ambient Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2.1 Terminals (rear panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3 Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.3.1 Reference Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 Controls, Display Elements and Terminals . . . 18
5.1 Front Panel SYSKON P500 / P800 / P1500 . . . . . . 18
5.2 Rear Panel P500 / P800 / P1500 . . . . . . . . . . . . . 20
5.3 Front Panel SYSKON P3000, P4500 . . . . . . . . . . . 22
5.4 Rear Panel SYSKON P3000, P4500 . . . . . . . . . . . 24
6 Menu Structure and Parameters . . . . . . . . . . 26
7 Analog Interface . . . . . . . . . . . . . . . . . . . . . . . 28
7.1 Connector pin assignments . . . . . . . . . . . . . . . . . 28
7.2 Auto-sensing mode . . . . . . . . . . . . . . . . . . . . . . . . 30
7.3 Status Signal Outputs . . . . . . . . . . . . . . . . . . . . . . 30
7.4 Regulating Output Voltage . . . . . . . . . . . . . . . . . . 31
7.5 Controlling Output Current . . . . . . . . . . . . . . . . . . 31
7.6 Voltage Monitoring Output . . . . . . . . . . . . . . . . . . 32
7.7 Current Monitoring Output . . . . . . . . . . . . . . . . . . 32
7.8 Trigger Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.9 Parallel Connection . . . . . . . . . . . . . . . . . . . . . . . . 34
7.9.1 Direct Parallel Connection . . . . . . . . . . . . . . . . . . . . . . . . 34
7.9.2 Master-Slave Parallel Connection . . . . . . . . . . . . . . . . . . . 35
7.10 Series Connection . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.10.1 Direct Series Connection . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.10.2 Master-Slave Series Connection . . . . . . . . . . . . . . . . . . . . 37
7.11 Varying the Internal Output Resistance Value . . . . 38
8 Descriptions of Operating Commands . . . . . . 39
9 Status and Events Management . . . . . . . . . . .56
10 Table of Operating and Query Commands . . . .58
10.1 Adjustable Functions and Parameters . . . . . . . . . 58
10.2 Queriable Functions and Parameters . . . . . . . . . . 60
10.3 Sequence Status Diagram . . . . . . . . . . . . . . . . . . . 62
10.4 Memory Structure . . . . . . . . . . . . . . . . . . . . . . . . . 63
11 System Messages . . . . . . . . . . . . . . . . . . . . .64
12 Operating Software . . . . . . . . . . . . . . . . . . . . .66
13 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
14 Order Information . . . . . . . . . . . . . . . . . . . . . .70
15 Repair and Replacement Parts Service
Calibration Center* and Rental
Instrument Service . . . . . . . . . . . . . . . . . . . . .70
16 Product Support . . . . . . . . . . . . . . . . . . . . . . .70
17 Manufacturer’s Guarantee . . . . . . . . . . . . . . .70
Note
These operating instructions describe devices as from
firmware version 005, see chapter 2.4.1.
GMC-I Messtechnik GmbH 3
1 Initial Inspection – Warnings
When unpacking the instrument, make sure that the
KONSTANTER and all included accessories are fully intact and
have not been damaged during transport.
Unpacking
• Other than the usual care exercised in handling electronic
equipment, no additional precautions are required when
unpacking the instrument.
• The KONSTANTER is delivered in recyclable packaging, which
provides for adequate protection during transport as substan-
tiated by testing. If the instrument is repacked at a later point
in time, the same packaging or its equivalent must be used.
Visual inspection
• Compare the order number or type designation included on
the packaging and/or the serial plate with the particulars
shown in the shipping documents.
• Make sure that all accessory components have been included
(seechapter 14 “Options and Accessories”).
• Inspect the packaging, as well as mechanical instrument and
accessory components for possible transport damage.
Complaints
If damage is discovered, immediately file a claim with the freight
forwarder (save the packaging!). If other defects are detected or in
the event that service is required, inform your local representative,
or contact us directly at the address included on the last page of
this handbook.
Use for Intended Purpose
Use of the KONSTANTER for its intended purpose is only fulfilled if
the instrument is used in accordance with the stipulations set
forth in the respective operating instructions, and is operated
within the specified power limits. The Konstanter may only be
used by persons with appropriate technical knowledge, or who
have received appropriate instruction.
In order to prevent danger during use, shock-proof connector
cables must be used when connecting power consumers. The
KONSTANTER’s output values (U, I) must be adjusted such that
no danger of overloading or destruction exists for the connected
power consumer.
Only then can the safety of the user, the instrument and the
device under test or the power consumer be assured.
Warnings and Safety Precautions
The KONSTANTER has been manufactured and tested in accord-
ance with the electrical safety regulations listed under Technical
Data as a safety class I device, and has been shipped from the
factory in flawless technical safety condition. In order to maintain
this condition and to assure safe operation, users must observe
all notes and warnings included in these operating instructions.
Attention!
!
A note concerning operation, practical advice or other
information which must be adhered to in order to prevent
damage to the KONSTANTER, and to assure correct
operation.
Warning!
An operating procedure, practical advice or other
information which must be adhered to in order to assure
safe operation of the KONSTANTER, and to prevent
personal injury.
The most important warnings are summarized below.
Warning!
Protective Grounding, PE Connection
The KONSTANTER may only be placed into operation
after the protective conductor has been connected.
Interruption or disconnection of the protective conductor
may result in
danger for the user.
The device is connected to the mains by means of a 3
conductor cable with mains plug.
Warning!
Opening the Housing Covers
Remove the mains plug from the outlet before opening
the housing. When the housing covers are opened,
voltage conducting parts may be exposed. Any contact
with these exposed conductive parts is life endangering.
For this reason, the instrument may only be opened by
trained personnel who are familiar with the dangers
involved.
Warning!
Repair by Trained Personnel
Maintenance and repair work, as well as internal
balancing, may only be performed by trained personnel
who are familiar with the respective functions, and the
dangers involved.
After the instrument has been disconnected from the
mains, wait approximately 5 minutes in order to allow the
capacitors to discharge themselves to safe voltage levels.
Warning!
Replacing Fuses
Only specified fuse types with the specified nominal cur-
rent rating may be used to replace blown fuses (see
Technical Data and specifications on the serial plate).
Manipulation of the fuses and/or the fuse holder is
prohibited.
Attention!
!
Impaired Safety
If it can be assumed that safe operation is no longer
possible, the KONSTANTER must be removed from ser-
vice and secured against inadvertent use. Safe
operation is no longer possible:
– If the KONSTANTER demonstrates visible damage or
transport damage
– If the KONSTANTER no longer functions
– After lengthy periods of storage under conditions
which deviate from the specified storage conditions
Significance of Symbols
Indicates EC conformity
This instrument fulfills the requirements of applicable European
and national EC directives. This is confirmed by means of the CE
mark.
A corresponding declaration of conformity can be requested
from GMC-I Messtechnik GmbH.
Observe ESDS guidelines
Warning concerning a point of danger
(attention: observe documentation!)
The device may not be disposed of with the trash.
Further information regarding the WEEE mark can be
accessed at www.gossenmetrawatt.com by entering
the search term WEEE.
!
Termékspecifikációk
| Márka: | Gossen Metrawatt |
| Kategória: | nincs kategorizálva |
| Modell: | SYSKON P1500 |
Szüksége van segítségre?
Ha segítségre van szüksége Gossen Metrawatt SYSKON P1500, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Gossen Metrawatt
4 Január 2025
4 Január 2025
4 Január 2025
4 Január 2025
4 Január 2025
1 Január 2025
17 December 2024
30 Augusztus 2024
29 Augusztus 2024
29 Augusztus 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Ganz
- nincs kategorizálva Mio
- nincs kategorizálva Eurochron
- nincs kategorizálva Kalorik
- nincs kategorizálva JK Audio
- nincs kategorizálva Sincreative
- nincs kategorizálva Memphis
- nincs kategorizálva Roadstar
- nincs kategorizálva Burris
- nincs kategorizálva SSV Works
- nincs kategorizálva LightZone
- nincs kategorizálva Reloop
- nincs kategorizálva NEO Tools
- nincs kategorizálva Maclean
- nincs kategorizálva Florabest
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025