Használati útmutató Hager 80040002

Hager nincs kategorizálva 80040002

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hager 80040002 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Berker GmbH & Co. KG - Zum Gunterstal - 66440 Blieskastel/Germany - Tel.: + 49 6842 945 0 - Fax: + 49 6842 945 4625 - E-Mail: info@berker.de - www.berker.com -
Operating and
assembly instructions
8004 00 01
Busapplicationunitflush-
mounted,system-/easylink
z
6LE000469B - 03/2021
1
(1)
(5)
(4)
(5)
(2)
(3)
(5)
(8)
(7) (6)
2
Safety instructions z
Electrical equipment may only be installed and
assembledbyqualifiedelectricians.Always
followtherelevantaccidentpreventionregulati-
ons.
Failuretocomplywiththeseinstallationinstruc-
tionsmayresultindamagetothedevice,fireor
otherhazards.
Wheninstallingandlayingcables,alwayscomply
withtheapplicableregulationsandstandardsfor
SELVelectricalcircuits.
Duringrenovationwork,protectthedevicefrom
pollutionbypaint,wallpaperpaste,dustetc.The
devicecanbedamaged.
Theseinstructionsareanintegralcomponentof
theproductandmustberetainedbytheend
user.
Designandlayoutofthedevice
Figure 1: Front view
Figure 2: Rear view
(1) Illuminated programming button
(2) Mounting device for fastening clamps
(3) Dust protection cover for user interface (suitable
for labelling eld sticker)
(4) User interface
(5) Screw holes for dismantling protection
(6) Plug-in interface for temperature sensor
(7) KNX bus connection terminal
(8) Attachment claws
Function
System information
This device is a product of KNX system and corre-
sponds to the KNX guidelines. Detailed specialised
knowledge obtained from KNX training courses
is required for comprehension. The planning, installa-
tion and commissioning are carried out with the help
of KNX-certi ed software.
systemlinkstart-up
The function of the device is software-dependent.
The software is to be taken from the product databa-
se. You can nd the latest version of the product da-
tabase, technical descriptions as well as conversion
and additional support programmes on our website.
easylinkstart-up
The function of the device is con guration-depen-
dent. The con guration can also be done using
devices developed specially for simple setting and
start-up.
This type of con guration is only possible with
devices of the easy link system. easy link stands
for easy, visually supported start-up. Precon gured
standard functions are assigned to the in/outputs by
means of a service module.
Correct use
- Attaching application modules, e.g. push-button,
thermostat, to the KNX system
- Installation into wall box according to DIN 49073
Productcharacteristics
- Start-up and programming in S-mode and E-mode
- Localisation function by integrated buzzer (siren)
- Connection for external temperature sensor
- Integrated dust protection cover for protection of
the user interface
Information for electricians
Installation and electrical connection
DANGER!
Touchinglivepartsintheinstallation
environmentcanresultinanelectric
shock!
Anelectricshockcanbelethal!
Disconnecttheconnectingcables
beforeworkingonthedeviceand
coveralllivepartsinthearea!
ç
Connectingandinstallingthedevice
Connect bus line via KNX bus terminal (7): red +,
black –.
Connect external temperature sensor via connec-
ting terminal (6) if necessary.
For mounting in a ush-mounted wall box use
xing claws (8) or in a hollow wall wall-box use
screws for  xing.
Mount the device into the wall box in the correct
position.
If no application module is mounted, close dust
protection cover for user interface.
6LE000469B
Berker GmbH & Co. KG - Zum Gunterstal - 66440 Blieskastel/Germany - Tel.: + 49 6842 945 0 - Fax: + 49 6842 945 4625 - E-Mail: info@berker.de - www.berker.com -
6LE000469B - 03/2021
Start-up z
systemlink-Loadingthephysicaladdressand
applicationsoftware
The device is mounted and connected to the KNX
bus. Application module is not mounted. The pro-
gramming button and LED are accessible.
The physical address is only ever assigned for
one device. Only one device can ever be in pro-
gramming mode.
Switch on bus voltage.
Press programming button (1).
The button lights up.
If the button does not light up, no bus voltage is
present.
Load the physical address into the device.
The programming LED goes out.
Load application software into the device.
Note the physical address on the bus application
unit (3) and on the associated application module.
The application software of the application module
can be fully loaded into the bus application unit.
The bus application unit automatically detects the
application module after mounting.
easylink
Information on the system conguration can be taken
from the extensive description of the service module
easy link.
Appendix
Technicaldata
KNX Medium TP 1
Start-up mode system link, easy link
Rated voltage KNX DC 21 ... 32 V SELV
Connection mode KNX bus connecting terminal
Power consumption KNX max. 150 mW
(with application module)
User interface
output power max. 100 mW
Dimensions (W x H x D) 71 x 71 x 32 mm
Clamping range of attachment claws 52 … 70 mm
Degree of protection IP20
Protection class III
Operating temperature -5 … +45 °C
Storage/transport temperature -20 … +70 °C
Standards EN 60669-2-1; EN 60669-1
EN 50428
Troubleshooting
Bus operation is not possible
Cause: Bus voltage is not present.
Check bus connection terminals for correct
polarity.
Check bus voltage by briey pressing the pro-
gramming button (1), red LED lights up if bus
voltage is present.
Warranty
We reserve the right to make technical and formal
changes to the product in the interest of technical
progress.
Our products are under guarantee within the scope
of the statutory provisions.
If you have a warranty claim, please contact the
point of sale or ship the device postage free with a
description of the fault to the appropriate regional
representative.

Termékspecifikációk

Márka: Hager
Kategória: nincs kategorizálva
Modell: 80040002

Szüksége van segítségre?

Ha segítségre van szüksége Hager 80040002, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Hager

Hager

Hager ARF560D Útmutató

2 Április 2025
Hager

Hager ARF570D Útmutató

2 Április 2025
Hager

Hager ARF525D Útmutató

2 Április 2025
Hager

Hager ARF566D Útmutató

2 Április 2025
Hager

Hager ARF556D Útmutató

2 Április 2025
Hager

Hager CF240J Útmutató

2 Április 2025
Hager

Hager CE463J Útmutató

2 Április 2025
Hager

Hager ARF520D Útmutató

2 Április 2025
Hager

Hager ARF506D Útmutató

2 Április 2025
Hager

Hager ARF575D Útmutató

2 Április 2025

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025