Használati útmutató JL Audio Stealthbox SB-SMRT-4-2/8W3v3

JL Audio mélynyomó Stealthbox SB-SMRT-4-2/8W3v3

Olvassa el alább 📖 a magyar nyelvű használati útmutatót JL Audio Stealthbox SB-SMRT-4-2/8W3v3 (4 oldal) a mélynyomó kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

I N S T A L L A T I O N G U I D E

for the

SB-SMRT-4-2/8W3v3

SKU# 94448

2008 & Up Smart fortwo

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-

specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation

professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle

properly. If you prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox ® be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

S T E P 1

Read all of the instructions through once before starting the

work. We know you’ve seen this warning before but, if

you only follow each step as it comes, the progression

won’t make sense, if you read everything all the way

through, you’ll understand, the job will be easier.

Clean out the passengers side of the vehicle so that you have

a comfortable place to work.

Continued on Next Page

S T E P 2

Remove the carpeting and, the foam underlay as if you were

accessing the battery (refer to the vehicles owners manual if

necessary).

S T E P 3

Under the passengers end of the dash there is a Torx screw

that holds the dash end trim panel in place, remove it and,

the trim piece.

SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288

INSTALLATION

D I F F I C U L T Y :

OUT

ESTIMATED TIME:

3 HOURS

Continued on Next Page

SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288

S T E P 7

On the Bottom end of the 1/4-20 All Threaded Rod, install

the Bottom Bracket as shown (approximately 1- 1 1/4” from

the bottom), using included 1/4-20 Nuts, Washers and, Split

Lock Washer.

DO NOT TIGHTEN THIS ASSEMBLY YET!

S T E P 6

Looking from under the dash, near the front of the vehicle,

there is a flange just under the top of the dash that has a

factory hole . Assemble the included Top Bracket and,

1/4-20 All Threaded Rod by putting on a 1/4-20 Nut and,

Split Lock washer then threading the rod into the bracket so

that just a few threads come out on the top side. Tighten the

1/4-20 Nut and, Split Lock washer to the Top Bracket. Once

the Top Bracket/ All Threaded Rod have been assembled,

bolt the other end of the Top Bracket to the flange using

the included 3/8-16 x 1” Hex Head Bolt, Nut, Washers and,

Split Lock Washer then rotate the Bracket so that it rests

on the top of AC system as shown, tighten down all of this

S T E P 5

Looking into the end of the dash, you will notice the

aluminum extrusion that is the frame of the dash. There is an

exposed slot, slide the included 1/4-20 Speed Clip over this

notch as shown.

S T E P 4

Once the trim piece is removed, there are three Torx screws

that hold the dash end piece in place, remove those and the

end piece.

Page 2 • JL Audio, Inc 2016

D E T A I L

Install the included right angle bracket as shown through

the slot in the dash extrusion using the included

3/8-20 Nut, Washers, 3/8-16 x 1 1/2” Hex Head Bolt, and, Split

Lock washer. The end with the hole closest to the bend is

against the dash extrusion. Slide the bracket all the way

towards the center of the vehicle, oriented as shown.

DO NOT TIGHTEN THIS ASSEMBLY YET!

S T E P 1 0

Attach the wire from the amplifier to the terminals on the

Stealthbox®

S T E P 9

Remove the woofer from the enclosure. Mount the

Elevated Bracket to the Stealthbox® as shown with the slot-

ted end exposed and pointing towards the top of the enclo-

sure, using the included 1/4-20 x 1” Hex Head Bolt, Split Lock

washer and Washer. Snug this hardware down so that it isn’t

loose but,

DO NOT TIGHTEN THIS ASSEMBLY YET!

S T E P 8

This picture is only to illustrate where the DETAIL below is

located, the enclosure and, woofer have NOT been mounted

yet. Where the arrow is pointing is where the DETAIL below

is located.

Continued on Next Page

SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288

S T E P 1 4

Rotate the Bottom Bracket on the 1/4-20 All Threaded Rod

so that it lines up with the threaded insert in the Stealthbox®,

you may need to raise or lower the position of the Bottom

Bracket on the All Threaded Rod in order to align everything.

Install the included 3/8-16 x 1” Hex Head Bolt, Split Lock

Washer and Washer as shown, securing the Stealthbox® via

it’s Threaded insert to the Threaded Rod.

DO NOT TIGHTEN THIS ASSEMBLY YET!

S T E P 1 3

Rotate the Elevated Bracket so that the slotted end is over

the Speed Clip (as shown) and, install the included

1/4-20 x 1” Hex Head Bolt, Split Lock washer and Washer.

DO NOT TIGHTEN THIS ASSEMBLY YET!

S T E P 1 2

Looking at the end of the dash, you should see the Elevated

Bracket pointing up next to the previously installed Speed

Clip. (See Arrow)

S T E P 1 1

Slide the enclosure up into place, it’s a tight fit and, you’ll

need to move it around a little but if you start as shown, it

will go in without any problems.

Page 3 • JL Audio, Inc 2016

S T E P 1 6

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an

amplifier recommendation and basic set-up help.

S T E P 1 5

Install the included, 3/8-16 x 1” Hex Head Bolt, Split Lock

washer and Washer through the Right Angle Bracket installed

in STEP 8 into the Stealthbox® as shown.

NOW YOU NEED TO TIGHTEN ALL OF THE PREVIOUSLY

INSTALLED HARDWARE!

Re-install the woofer into the enclosure.

Re-assemble the end of the dash in the reverse order that

it was disassembled, re-install the Foam Underlay and the

Carpet.

Termékspecifikációk

Márka:	JL Audio
Kategória:	mélynyomó
Modell:	Stealthbox SB-SMRT-4-2/8W3v3

Szüksége van segítségre?

Ha segítségre van szüksége JL Audio Stealthbox SB-SMRT-4-2/8W3v3, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók mélynyomó JL Audio

JL Audio FS108-W5 Útmutató

31 Március 2025

JL Audio Stealthbox SB-T-TACDC12/10TW3 Útmutató

31 December 2025

JL Audio Stealthbox SB-GM-SLVCRW/10TW3 Útmutató

31 December 2025

JL Audio Stealthbox SB-F-MUCUPE2/13W3v3 Útmutató

31 December 2025

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/GA Útmutató

31 December 2025

JL Audio Stealthbox SB-GM-CTRIP/10TW3/UF Útmutató

8 December 2024

JL Audio Stealthbox SB-GM-ESC/10W1v3/TN Útmutató

8 December 2024

JL Audio SGR-10TW3 Útmutató

13 Október 2024

JL Audio TW1 Útmutató

6 Október 2024

JL Audio 12W0v3 Útmutató

4 Október 2024

Útmutatók mélynyomó

Legújabb útmutatók mélynyomó

Phase Technology IW200-II Útmutató

4 Április 2025

Wet Sounds ZERO 10 S4 XZ-W Útmutató

2 Április 2025

SoundTube CM1001D Útmutató

2 Április 2025

Phase Technology PL-12p Útmutató

30 Március 2025

ETON Graphit 8-2 Útmutató

19 Március 2025

ETON Graphit 8-4 Útmutató

19 Március 2025

ETON Graphit 10-4 Útmutató

19 Március 2025

ETON MW 10 FLAT Útmutató

19 Március 2025

ETON PW 8 Útmutató

19 Március 2025

ETON USB 6 AR Útmutató

19 Március 2025