Használati útmutató Kathrein KAZ 10
Kathrein
Megkönnyebbülés
KAZ 10
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kathrein KAZ 10 (3 oldal) a Megkönnyebbülés kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 4.5 felhasználó értékelte átlagosan 4.4 csillagra
Oldal 1/3
About This Guide
This document is part of the product.
►Do not install or use the device until you have read and understood
this document.
►
Keep this document for reference throughout the service life of the
device. Pass this document on to any new owner or user.
For the most up-to-date version of this document, go to
www.kathrein-ds.com.
Storage and Transport
►
Transport and store the device in its original packaging.
►Make sure there is no water condensation build-up.
Scope of Delivery
●KAZ 10
●Pre-assembled equipotential bonding wire
●Mounting screws and rawlplugs
●Instructions for use
Features
■
Protection of system components in DVB-S/C/T reception and distri-
bution systems
■
Deployment of KAZ 10 increases the surge discharge capability of
KAZ11 and KAZ 12
■Fulfils categories C2/C3/B2/D1 according to EN 61643-21
■Remote feeding for DC voltages from 0...+20 V / max. 0.4 A
■Passage for 22 kHz and DiSEqC™ signals
■Impedance: 75 Ω
■For indoor installation only
■
KAZ 10 2180000001
Surge Protection Device, 5-way
Installation and Safety Instructions
Danger to life from electric shock and fire hazard due
to electric current!
►Connection and installation of the device may only be
carried out by a qualified electrician. National regula-
tions and safety regulations must be complied with
(see also EN 60728-11).
►Before installation, the equipment must be checked
for external damage. Should there be damage or
another defect, the equipment must not be installed.
►The use of the device is permissible only under the
conditions listed and shown in these installation
instructions. In case of loads which exceed the indi-
cated values, the equipment and any electrical equip-
ment connected to it can be destroyed.
►
Make sure that the maximum operating voltage of
the system does not exceed the highest continuous
voltage UDC and the maximum remote supply current
IDC.
►
The device is designed for a clean and dry environ-
ment. Do not expose the device to any mechanical
and/or thermal stress that exceeds the limits of the
specified technical data.
►The device must be installed so that it is inaccessible
to children.
►
The equipment must be provided with an equipoten-
tial bonding wire (Cu, at least 4 mm2).
To increase the protective eect, it is recommended to
use KAZ 11 as a fine protection directly before the device
to be protected as well as KAZ 12 as a coarse protection at
the house entry point (see Fig. 4).
Intended Use
►
This device is intended solely for installation in DVB-S/C/T reception
and distribution systems. It may only be installed by trained specia-
lists.
►Any use other than that specified or failure to observe these applica-
tion notes will invalidate the warranty or guarantee.
►
The manufacturer accepts no liability for accidents caused by the
user opening the unit.
►Opening the unit and attempting to repair it yourself voids all
warranty claims.
Other Measures
►
With remotely-fed antenna amplifiers, no additional protective circuit
is necessary. With mains-fed devices, an additional protective device
for the mains feed is required (e.g. S-Protector, NSM-Protector or
DEHNsafe). The PE connection of the mains feed must be connected
with the grounding connection of the KAZ 10 surge protector at low
resistance.
►
If cable systems require the use of a gas discharge arrester at the
building transfer point (BTP), a decoupling distance of at least 1 m
between the BTP and the KAZ 10 is required to ensure coordina-
tion of the two protective measures. The use of an upstream gas
discharge arrester (e.g. KAZ 12) increases the surge current capabi-
lity of the KAZ 10 surge protector.
►Equipotential bonding is performed according to Fig. 3. Additio-
nally, the ground terminals must be connected with short cables
(Cu,4mm2).
Connecting the KAZ 10
1. Connect the OUT side of the KAZ 10 to the inputs of the devices to
be protected (multi-switch, amplifier, ...). Use short coaxial cables
with F connectors. Make sure that each system component is
always connected to the equipotential bonding and, if necessary,
insert additional grounding blocks (e.g. EMU 21).
2. The lateral mounting brackets (see 1 Fig. 1) allow you to mount the
surge protector on a flat surface.
3. Connect the cables coming from the satellite antenna (see 2 Fig. 1),
and any existing terrestrial antennas to the IN side of the surge
protector.
4. Connect the housing via the lateral earthing screw (see 3 Fig. 1) to
the local equipotential bonding by the shortest possible route.
IN
OUT
KAZ 10
K-019
218000001
protected
1
2
3
47 - 2400 MHz
DE - 83022 Rosenheim
Fig. 1: Connecting the KAZ 10
Termékspecifikációk
| Márka: | Kathrein |
| Kategória: | Megkönnyebbülés |
| Modell: | KAZ 10 |
Szüksége van segítségre?
Ha segítségre van szüksége Kathrein KAZ 10, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Megkönnyebbülés Kathrein
31 Július 2024
10 Július 2024
Útmutatók Megkönnyebbülés
- Megkönnyebbülés Claypaky
- Megkönnyebbülés Rocktrail
- Megkönnyebbülés Auriol
- Megkönnyebbülés Beghelli
- Megkönnyebbülés 4K5
- Megkönnyebbülés Brilliant
- Megkönnyebbülés Lideka
- Megkönnyebbülés Hive
- Megkönnyebbülés Blaupunkt
- Megkönnyebbülés Fluval
- Megkönnyebbülés Medisana
- Megkönnyebbülés OneConcept
- Megkönnyebbülés EtiamPro
- Megkönnyebbülés Hama
- Megkönnyebbülés MeLiTec
Legújabb útmutatók Megkönnyebbülés
9 Április 2025
9 Április 2025
9 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
7 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025