Használati útmutató Paasche TG-3AS

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Paasche TG-3AS (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 23 ember találta hasznosnak.

/ 2 PDF

INSTRUCTIONS AND PARTS LIST TG-TALON

TG TALON – Airbrush

Double Action - Internal Mix - Gravity Feed -

PTFE Packings.

WARNING: Spray materials may be harmful if

inhaled or allowed to come into contact with the

skin or eyes. Consult the product label and material

safety data sheet supplied for the spray material.

Follow all safety precautions. CAUTION: Well

Ventilated Area Required to remove fumes, dust or

overspray. Maximum Air Pressure 75 P.S.I.

TG Specications:

•Dual Action • Gravity Feed • Internal Mix • Cutaway Handle w/ Pre-set Needle Stop • PTFE Packing

TT-2, TN-2, and TA-2 Components come installed on Talon.

Options for Talon:

.2mm head (TT-0, TN-0, TA-0 components) - Great for jobs requiring “extremely ne detail”.

.25mm head (TT-1, TN-1 and TA-1 components) - Great for jobs requiring ne detail

.66mm head (TT-3, TN-3 and TA-3 components) - Great for spraying Metallics, Pearlescent and Thicker

Paints

.66mm Fan Aircap (TAF-3, TN-3 and TT-3) Will give a 2-1/2 to 3 inch fan pattern.

Working Pressures:

•Operating pressures 15-55 PSI; Maximum pressure 85 PSI. Fan aircap needs 20 PSI or more.

•20-30 PSI is best for detail spraying w/ properly thinned paint

•Use the higher pressures for thicker material where ne detail is not critical or, thin the paint to allow

lower pressures.

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with index nger comfortably over the nger button.

1.Attach air hose to air supply and to airbrush. If using a regulator set pressure between 20 -55 PSI.

Airbrush Operation:

1.Attach air hose to air supply and to airbrush.If using a regulator set pressure between20-55psi.

2.Press down on Finger Trigger to release air and pull back on trigger to control quantity of color.

3.Speed of movement controls density of color and fading e󰀨ects at beginning and end of strokes.

4.Practice this movement until you can spray a ne line or a broad pattern without heavy build up at the

beginning or end of your strokes.

5.For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on

the Finger trigger to release a small amount of paint.

6.For background work and broad e󰀨ects, hold the airbrush away from the work surface and pull back

on Finger trigger to release required amount of color.

NO. PART DESCRIPTION

1.XI-41Crown Cap

1a. TAF-3Fan Aircap for .66mm head -

2.TA-1,TA-2,TA-3Aircap (.25mm, .38mm, .66mm)

(Size TA-1 head is used with size 0 and 1 tip)

3.TT-0,TT-1,TT-2,TT-3Tip(.2mm,.25mm,.38mm,.66mm)

4.MIL-12“O” Ring for TG-30 Shell

5.TG-30Shell Assembly

6.TG-4Cup Cover

7.TAL-8Packing Assembly PTFE

8.TAL-37Trigger

9.TAL-14Valve Casing

10. TAL-36Valve Plunger (Includes O-ring)

10a. A-53(Optional) Pack of (6) O-rings

11. TAL-15Valve Adapter (Includes O-ring)

11a. TAL-22(Optional) Pack of (6) O-rings

12.A-22Spring

17.TAL-18Rocker Assembly

18. MIL-11Needle Spring

19. TAL-17Spring Housing

20. TAL-19Needle Lock Nut

21. MIL-12“O” Ring for TG-34 Handle

22. TAL-20Handle

23. 3A-4“O” Ring

24.TN-0,TN-1,TN-2, TN-3 Needle

(.2mm .25mm .38mm .66mm)

25. TAL-35Allen Wrench

26. TAL-28Wrench

27.TAL-33Needle Stop

*Note: Etch lines on Items

2 3 and 24. indicate size.

All should match when

installed on airbrush.

Termékspecifikációk