Használati útmutató Qazqa 44083
Qazqa
Megkönnyebbülés
44083
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Qazqa 44083 (4 oldal) a Megkönnyebbülés kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 3.5 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/4
Dark WL I PIR LED Solar
MODEL: 44083
INTRODUCTION
The Light works with a build-in PIR (Passive Infra Red) sensing device
which is connuously scanning for heat-source moving in its detec-
on scope. Once a heat-source (such as a human or a car) is detected
in that area, the light switches on immediately and automacally to
illuminate your pathways, steps, paos, porches, or anywhere you
select for safety, convenience or security. The light remains on while
heat-source moving stays in the detecng scope.
■ INSTALLATION SUGGESTIONS
For best detecng effect of PIR, we suggest you take the following
points into account:
● Ideally, for maximum detecon range, the Light should be moun-
ted 1.8 to 2.5 meters (6 to 8 ) above the area to be scanned
(refer to Fig.1A).
● To avoid damage to some components, please do not aim the
sensor towards the sun.
● To avoid annoying unexpected triggering, the sensor should stay
away from heat sources such as barbecues, Air-condioners, other
outside lighng, moving cars and flue vents.
● To avoid annoying unexpected triggering, please keep the sensor
away from strong electromagnec disturbance source.
● Do not aim the sensor at reflecve surfaces such as smooth white
walls, swimming pools, etc...
● The PIR sensor’s detecon range (about 7 meters at 100°round)
may vary slightly depending on the mounng height and locaon.
The detecon range may also alter with environment temperature
change.
● Before select a place to install, please note that sensor is more
sensive to movement across the scan area than to movement
directly toward or away from the sensor (refer Fig.1B). If heat
Side View
Front View
100°
4.5 M
0.7 M 7 M
2 M
Fig 1( A )
Detection Range
153 mm
157 mm
109 mm
2
INSTALLATION STEPS
1．Drill two holes on wall where you want the light be mounted on
and put the plasc plugs into wall holes. Then Mount the mount
plate by screws (refer to Fig 2 A)
2．Fix the light on the wall plate and lock it by turning the key.
Remove the key and keep it for future use. (refer to Fig 2 A)
OPERATION
1. Mount the light on place where it can get max. DIRECT SUNLIGHT
in dayme. The inside baeries are charged by solar cell. The
more direct sunlight solar cell receives in dayme, the longer the
light will run. It is beer to charge the solar cell in sunlight for up
to one day before switching on it, so that the light can work with a
full charge.
2. Modes of slide switch:
AUTO: Normal work automacally
ON: Constantly light on as emergency lamp
OFF: Power off for storage and long me charging
source moves directly towards to or away from the sensor and not
across, the detecon range will be relavely reduced (refer to
Fig.1C) .
Fig 1( C ) Fig 1( B )
Good Detecting Not Good Detecting
TECHNICAL DETAILS:
Baery: 3 pieces of AA 1.2V-600mAh baeries
Waage: 2×0.5 W LED, stac ≤0.64 mW
Voltage: 3.6V DC
Duraon me: 60±10 sec.
Detecon range: 100º (round) , Max. 7 meters
Weatherproof: IP44
FEATURE
1. While light is turn on for the first me, LED light on and PIR start
warming up. Then, LEDs stay on for 40 sec., then flash for 3 mes
and shi to detecon mode.
2. At night, LEDs will remain on for 60 seconds since the last move-
ment is detected. If a movement is detected during the light-on
me, duraon me will be renewed and LEDs remain ON for
another 60 seconds.
3. In daylight or bright environment, PIR’s Lux control works, move-
ment does not acvate the PIR.
3
Trouble shoong and user hints
Note: all PIR sensors in dry and cold environment are more sensive
than that in wet and heat environment.
PROBLEM POSSIBLE CAUSE
SUGGESTED
REMEDY
Light does not switch
on when there is
movement in the
detection area.
1. Batteries are used out
Recharge batteries
2. Nearby lighting is too bright.
Re-direct sensor or
relocate the unit
3. Sensor towards wrong direction
Re-direct the PIR
Light switches on for no
apparent reason
(false trigger)
1. Heat sources such as aircon, vents, heater flues,
barbecues, other outside lighting, moving cars are
activating the sensor.
-
Place it away from
these sources.
2. Animals/birds e.g. possums or domestic animals.
Redirecting light may
help.
3. Reflection from swimming pool, or reflective surface.
Re-directing light
Light switches on
during daytime
Something shadow the Lens of PIR Sensor
Redirecting light
Termékspecifikációk
| Márka: | Qazqa |
| Kategória: | Megkönnyebbülés |
| Modell: | 44083 |
Szüksége van segítségre?
Ha segítségre van szüksége Qazqa 44083, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Megkönnyebbülés Qazqa
31 December 2025
22 Augusztus 2024
22 Augusztus 2024
21 Augusztus 2024
21 Augusztus 2024
21 Augusztus 2024
21 Augusztus 2024
21 Augusztus 2024
21 Augusztus 2024
20 Augusztus 2024
Útmutatók Megkönnyebbülés
- Megkönnyebbülés Ape Labs
- Megkönnyebbülés SolarlampKoning
- Megkönnyebbülés Lenoxx
- Megkönnyebbülés Goobay
- Megkönnyebbülés Enerdan
- Megkönnyebbülés Beghelli
- Megkönnyebbülés Wetelux
- Megkönnyebbülés ESYLUX
- Megkönnyebbülés Crivit
- Megkönnyebbülés Blumfeldt
- Megkönnyebbülés Chrome-Q
- Megkönnyebbülés Martin
- Megkönnyebbülés Dydell
- Megkönnyebbülés Fenix
- Megkönnyebbülés Corsair
Legújabb útmutatók Megkönnyebbülés
9 Április 2025
9 Április 2025
9 Április 2025
8 Április 2025
8 Április 2025
8 Április 2025
7 Április 2025
5 Április 2025
5 Április 2025
5 Április 2025