Használati útmutató Sanyo SAP-KRV244

Sanyo légkondicionáló SAP-KRV244

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sanyo SAP-KRV244 (10 oldal) a légkondicionáló kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/10

English

3-8. Mounting

(1) To install the indoor unit, mount the indoor unit

onto the 2 tabs on the upper part of the rear plate.

(2) Hold down the air discharge outlet and press the

lower part of the indoor unit until it clicks to

securely fasten to the 2 tabs on the lower part of

the rear plate. (Fig. 33)

For tubing, choose either the right or left tubing direc-

tion and follow the steps below. This work can be made

easier by placing padding material (such as styrofoam)

at the rear right side of the indoor unit. (Fig. 34a)

Or extend the support on the back of the indoor unit as

a stand to make your work easier. (Fig. 34b)

IRight-side tubing

(1) Shape the refrigerant tubing so that it can easily

go into the wall hole. (Fig. 35a or 35b)

(2) Push the wiring, refrigerant tubing, and drain hose

through the hole in the wall. Adjust the indoor unit

so it is securely seated on the rear panel. (Fig. 36)

(3) Carefully bend the tubing (if necessary) to run

along the wall in the direction of the outdoor unit

and then tape as far as the fittings. (See Caution

on page 10 or 15 in the outdoor unit installation

manual.) The drain hose should come straight

down the wall to a point where water runoff won’t

stain the wall.

(4) Connect the refrigerant tubing to the outdoor unit.

(After performing a leak test on the connecting

part, insulate it with the tubing insulation. (Fig. 37))

Also, refer to Section 3-6. Tubing connections in

the outdoor unit installation manual.

(5) Assemble the refrigerant tubing, drain hose, and

inter-unit wiring as shown in Fig. 37.

NOTE

Cover

Refrigerant

tubing

Rear panel

Drain hose

Inter-unit

wiring

Fig. 35a

Fig. 36

Fig. 33

P hus

Insulation

Paddi materialng

Fig. 34a

Rear panel

(SAP-KRV96)

(SAP-KMRV74, KMRV94, KMRV124)

(SAP-KMRV76, KMRV96, KMRV126)

(SAP-KRV184, KRV244)

(SAP-KRV186, KRV246)

Fig. 34b

Fig. 37

Wall cap

Tab

Rear pa eln

Refri era tg n

t biu ng

Inter- itun

wiring

Drai hon se

Fig. 35b

(SAP-KMRV74, KMRV94, KMRV124)

(SAP-KMRV76, KMRV96, KMRV126)

(SAP-KRV184, KRV244)

(SAP-KRV186, KRV246)

(SAP-KRV96)

English

Hole i walln

Be t partn

Narrow t beu

Wide t beu

Rear pa eln

Fig. 38a

Drai capn

Drai ho en s

Fig. 39a

ILeft-side tubing

(SAP-KMRV74EH, KMRV94EH, KMRV124EH,

KMRV76EH, KMRV96EH, KMRV126EH,

KRV184EH, KRV244EH, KRV186EH, KRV246EH)

(1) Lead the tubing and drain hose through the wall,

allowing sufficient length for connection. Then

bend the tubing using a tube bender to make the

attachment. (Fig. 38a)

(2) Switch the drain hose and drain cap.

Switching drain hose and drain cap

(a) Locate the drain hose and the drain cap.

(Fig. 39a)

(b) Remove the screws fastening the drain hose

on the right side, and pull out the drain hose

to remove it. (Fig. 39a)

on the left side. (If you cannot pull it off by

hand, use a long-nose pliers.)

(d) Reattach the drain hose to the left side and

the drain cap to the right side. (Fig. 40a)

Drain hose

Slide the drain hose fully onto the drain pan outlet

until the drain hose edge is pushed into the insu-

lation. Check that the screw holes in the drain

bracket and the drain pan outlet are aligned and

securely in contact, then fasten them with the

screw. (After attaching the drain hose, check that

it is attached securely.) (Fig. 40c)

Drain cap

Use a Phillips screwdriver to push the drain cap in

firmly. (If it is difficult to push in, wet the cap with

water first.)

(3) Install the indoor unit on the rear panel.

(4) Connect the tubing and wiring led inside from out-

doors.

(5) After completing a leak test, bundle the tubing

together with armoring tape and store it inside the

tubing storage area at the back of the indoor unit

and hold it with clamps. (Figs. 40a and 41a)

Fig. 40a

Fig. 40bFig. 40c

Fig. 41a

Refri era t t big n u ng

I ter- it wirin un ng

Screw

Drai ho en s

Drai pa o tletn n u

Screw hole

Drai bracketn

Drai capn

Clamp

Drai ho en s

Drai bracketn

I lationsu n

English

ILeft-side tubing

(SAP-KRV96EHDS)

(1) Lead the tubing and drain hose through the wall,

allowing sufficient length for connection. Then

bend the tubing using a tube bender to make the

attachment. (Fig. 38b)

(2) Switch the drain hose and drain cap.

Switching drain hose and drain cap

(a) Grasp the corners of the bottom left and right

indoor unit covers, and press down on the

bottom while lifting each cover up to remove

it. (Fig. 39b)

(b) Locate the drain hose and the drain cap.

(Fig. 39c)

the drain fitting from the stopper, then check

the position of the drain fitting on the end of

the hose, and turn the hose while pulling to

remove it. (Fig. 39d)

(d) Screw the drain hose all the way inside. Turn

the hose so that the protruding part of the

drain fitting comes below the stopper as

shown in the figure. It will be easy to insert

when water is added. (Fig. 39d)

(e) Align the tabs of the removed cover with the

grille tabs, and then lower the cover to install

it.

Drain cap

Use a Phillips screwdriver to push the drain cap in

firmly. (If it is difficult to push in, wet the cap with

water first.)

(3) Install the indoor unit on the rear panel.

(4) Connect the tubing and wiring led inside from out-

doors.

(5) After completing a leak test, bundle the tubing

together with armoring tape and store it inside the

tubing storage area at the back of the indoor unit

and hold it with clamps. (Figs. 40d and 41b)

Fig. 38b

Bottom left cover

Fig. 39b

Fig. 39d

Fig. 41b

Refri era t t big n u ng

I ter- it wirin un ng

Drai capn

Clamp

Drai hon se

Hole i walln

Rear pa eln

Be t partn

Wide t beu

Narrow t beu

Fig. 40d

Stopper

Drai fittin ng

Drai ho en s

Stopper Drai ho en s

Drai fittin ng

Drai capn

Drai hon se

Fig. 39c

Termékspecifikációk

Márka:	Sanyo
Kategória:	légkondicionáló
Modell:	SAP-KRV244

Szüksége van segítségre?

Ha segítségre van szüksége Sanyo SAP-KRV244, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók légkondicionáló Sanyo

Sanyo SAP-KMRV124 Útmutató

2 Augusztus 2024

Sanyo SAP-KMRV76 Útmutató

31 Július 2024

Sanyo KR12AEH Útmutató

31 Július 2024

Sanyo XS3632 Útmutató

31 Július 2024

Sanyo SAP-KRV93EHE Útmutató

29 Július 2024

Sanyo KMS1212 Útmutató

26 Július 2024

Sanyo TS4232 Útmutató

26 Július 2024

Sanyo XS1852 Útmutató

25 Július 2024

Sanyo SAP-KRV186 Útmutató

25 Július 2024

Sanyo SA-96P Útmutató

24 Július 2024

Útmutatók légkondicionáló

Legújabb útmutatók légkondicionáló

LG A09AWG Útmutató

10 Április 2025

Carson PA240 Útmutató

10 Április 2025

Carson PA340 Útmutató

10 Április 2025

Midea MUB-60HRN1 Útmutató

9 Április 2025

Fakir 1020 Útmutató

9 Április 2025

Daikin FWP17CATN6V3 Útmutató

9 Április 2025

Daikin FWP06CAFN6V3 Útmutató

9 Április 2025

Panasonic CS-45KA1E5 Útmutató

9 Április 2025

Daikin FXNQ63A2VEB Útmutató

9 Április 2025

Daikin FXNQ20A2VEB Útmutató

9 Április 2025