Használati útmutató Supermicro SuperServer 1018L-MP

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Supermicro SuperServer 1018L-MP (1 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 4 felhasználó értékelte átlagosan 4.3 csillagra

http://www.supermicro.comMNL-1604-QRG

Board Layout

SuperServer 1018L-MP Quick Reference Guide

Power Button

2 x USB Ports

Audio Port

Description

No.

Drive bay Installation/RemovalMEMORY

Caution

1

2

3

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



!



!



!

PositiontheSO-DIMMmod -1.

ule'sbottomkeysothatit

alignswiththereceptivepoint

ontheslot . Take note of the

Module’s side notches

and the locking clips on the socket

InserttheSO-DIMMmodule 2.

staight down.

Pressdownuntilthemodule 3.

locksintoplace.Thesideclips

willautomaticallysecurethe

SODIMMmodule,lockingit

intoplace .

To 4.Remove:Useyourthumbs

togentlypushthesideclips

nearbothendsawayfromthe

module.Thisshouldrelease

itfromtheslot.PulltheSO

DIMMmoduleupwards .

Installling2.5" SA ATDrives

1. Power down the system and unplug the AC/DC Power Adapter.

2. Remove the chassis cover.

3. Use screws to secure the drive into the hard drive bracket.

4. Use screws to secure the bracket/drive assembly into the middle holding bar

of the chassis as shown in the figure.

Beep Codes

1 beep - circuits have been reset (ready to power up).

5 short beeps + 1 long beep - No memory detected

in the system

1 continuous beep with front panel Overheat LED on -

system overheat

5 short beeps - display memory error

When a recoverable type of error occurs during

POST, BIOS will display a POST code that

describes the problem. BIOS may also issue one

of the following beep codes:

Front View & Interface

InionLEformatal D

SustntatDescrip io

BluePower On

Blinking WhiteHDD Activity

123

Descrip iotnNo.

PCI-E 2.0 p1-x16

Mini PCI-E scoket

JSD1 = SATA Disk on Module (DOM) Power

CPU socket

DIMMA1 Memory Slot

DIMMB1 Memory Slot

JTPM = TPM (Trusted Platform Management) Header

I-SATA2/3: SATA 2.0 ports (3Gb/s)

I-SATA0/1: SATA 3.0 ports (6Gb/s)

JBT1: CMOS Clear

1

2

3

4

5

6

7

8

9

10

5

6

1

I-SATA3

I-SATA2

JGPIO1

JPW2

JP1

JPCIE1

JSMB1

JBT1

BT1

COM4

COM

JAUDIO1

FAN2

FAN1

CA

JTPM1

JVR1

JL

JSD1

JD1

I-SATA0

I-SATA1

SP1

+

DIMMA1

DIMMB1

PW1

CMOS CLEAR

PCIE

mini

JUSB2LAN2 JUSBLAN1

42 3

10 7

89

A nlig

ÌMNL-1604-QRGcÎ

Termékspecifikációk