Használati útmutató Tripp Lite SRTHERMDUCT

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Tripp Lite SRTHERMDUCT (8 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/8
Owner’s Manual
1
SmartRack Accessories
Model: SRTHERMDUCT
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2012 Tripp Lite. All rights reserved.
Warranty
Registration:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
Table of Contents
Introduction 2
Parts List 2
Installation 3
Warranty & Warranty Registration 7
201204262-93-2958-EN.indd 1 6/4/2012 2:39:46 PM
2
Introduction
Tripp Lite’s SRTHERMDUCT is a 3 piece, adjustable venting and cable management system that will t on top of standard 42 or 48U
rack enclosures. The SRTHERMDUCT allows heat built up in a typical rack conguration to be vented upwards into your facility’s return
air duct or other standard ventilation system, helping your equipment perform at its peak while reducing your facility’s cooling and
energy costs.
Parts List
Cable Access Panel (1) Chimney Base (1) Adjustable Chimney
Slider (1)
Enclosure Bottom
Panel (1)
Rectangular
252mm x 476mm
Magnetic Vinyl Sheet
(6)
Cutout 252mm x
476mm x 325mm
Magnetic Vinyl Sheet
(1)
Cutout 252mm x
476mm x 452mm
Magnetic Vinyl Sheet
(1)
Rectangular 252mm x
137mm Magnetic Vinyl
Sheet (4) (48U rack
enclosures only)
M8 Screws (4) M4 Screws (4) M4 Nuts (16)
Tubular Door Seal Flat Door Seal
Rectangular 252mm x
68mm Magnetic Vinyl
Sheet (4) (45U rack
enclosures only)
201204262-93-2958-EN.indd 2 6/4/2012 2:39:48 PM
1
2
3 4
3
Assembling the Chimney Base
1 Position the 4 side panels of the Chimney Base in accordance
with Diagram 1 and secure the attachments with 8 of the M4
nuts that screw onto the pre-installed threaded posts.
Once assembled, this piece can be put aside for later use.
Installation
Assembling the Adjustable Chimney Slider
2 Position the 4 side panels of the Adjustable Chimney Slider
in accordance with Diagram 2 and secure the attachments
with the remaining 8 M4 nuts that screw onto the pre-installed
threaded posts.
Once both the Chimney Base and Slider have been assembled
you can move on to stacking.
Stacking the Chimney
3 With both the Chimney Base and Adjustable Chimney Slider
assembled, position and fit the slider on top of the base.
4 The holes in the sides of the Chimney Base and locking pins
in the sides of the Chimney Slider allow the chimney to be
adjustable in height with a range of 20” (flat, no height) to
34” (adjusted, full height). For installation purposes, it is
recommended to initially stack the two pieces in the 20” (flat,
no height) position until installed on the rack enclosure. To do
so, pull out the four locking pins and slide the Chimney Slider
all the way down over the Chimney Base into the 20” position
as seen in Diagrams 3 and 4.
201204262-93-2958-EN.indd 3 6/4/2012 2:39:49 PM

Termékspecifikációk

Márka: Tripp Lite
Kategória: nincs kategorizálva
Modell: SRTHERMDUCT

Szüksége van segítségre?

Ha segítségre van szüksége Tripp Lite SRTHERMDUCT, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Tripp Lite

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025