Használati útmutató Altronix 6062
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Altronix 6062 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 21 ember találta hasznosnak és 11 felhasználó értékelte átlagosan 4.9 csillagra
Oldal 1/2
6062 - Multi-purpose Timer
Overview:
Model 6062 programmable timer is suitable for many functions that require a timed operation e.g. Access Control Applications,
Siren/Bell Cut Off Module, Dialer Delay, Guard Tour Supervisory Timer, etc. Some optional functions include: One Shot, Delayed
Release, Delayed Operate, Delayed Pulse and Pulser/Flasher. A new feature has been added which provides a momentary relay acti-
vation at the end of a desired timing cycle. This feature eliminates the need for having to use two (2) timers to achieve this function.
Specifications:
Installation Instructions:
1. Mount 6062 in desired location/enclosure.
2. Set proper DC Input Voltage Dip Switch 3: 12VDC ON, 24VDC OFF.
3. Refer to Dip Switch Selection and Jumper Selection Tables for desired functions (e.g.: Timing, Trigger, Pulse)
4. Measure DC input voltage before powering device to ensure proper operation.
5. Refer to Terminal Identification Table and Typical Applications fig. 1 thru fig. 8. for desired wiring connections.
Note: When triggering via a N.O. (normally open), momentary or maintained trigger, connect the dry contact trigger to Pos (+)
and TRG terminals. When triggering via a N.C. (normally closed), momentary or maintained trigger, connect the trigger to Neg. (-)
and TRG terminals and install a resistor [for 12VDC - 2K (2,000 ohm) or for 24VDC - 4.7K (4,700 ohm)]
between the Pos (+) and TRG terminals (Fig. 8).
6. Enable the reset features:
- Cut J3 when power is removed the timer will reset and not re-trigger when power is restored unless a new trigger is applied.
Note: The closed trigger and delayed pulse options will not operate if the reset feature is desired.
Dip Switch Selection Table:
Dip # Off On
1 Relay energizes at the start of timing cycle.* Relay energizes at the end of timing cycle.*
2 1-60 Minutes timing range (trimpot adjustable). 1-60 Seconds timing range (trimpot adjustable).
3 24VDC operating voltage. 12VDC operating voltage.
4 Timing begins immediately upon trigger input. Timing starts after removal of trigger input.
* When relay energizes (LED is on) [N.O. & C] switch from open to close and [N.C. & C] switch from close to open.
Jumper Selection Table:
Number Function/Description
J1
Cutting J1 selects the pulser/flasher mode. Relay will flip ON and OFF
continuously in equally set timed intervals when timer is powered up.
J2
Cutting J2 puts timer in delayed output mode. Relay will pulse for 1 second at
the end of a preset timing cycle. *Dip Switch 1 must be ON for this function.
J3
6062 will go through an initial timing cycle when first powered up unless J3 is cut.
If J3 is cut, timing can only be initiated via TRG terminal.
Terminal Identification:
Terminal
Legend
Function/Description
TRG
Applying a positive voltage will activate timing cycle.
Trigger voltage range: 7-12VDC at 12 volt setting, 15-24VDC at 24 volt setting.
--- , + Connect 12 or 24VDC filtered and regulated voltage. Refer to Dip Switch Selection Table for voltage setting.
N.O., C, N.C. Dry form “C” relay contacts are rated 8 amp at 120VAC/28VDC.
•12VDCor24VDCoperationisselectable.
•Quickandextremelyaccuratetimerangeadjustmentfrom
1 sec. to 60 min.
•LEDindicatesrelayisenergized.
•Form“C”relaycontactsare8ampat120VAC/28VDC.
•CurrentDraw:Stand-by3mA,RelayEnergized40mA.
•TriggersviapositiveDC(+)voltage,drycontactclosure,
or removal of contact closure.
•Selectablerelayactivationatthestartorendofthe
timing cycle.
•One(1)secondmomentaryrelayactivationattheendof
the timing cycle (eliminates the need to use two (2) timers
for this function).
•Built-inresetfeaturewhichcancelstimingcycle.
•Repeat(pulser/flasher)mode.
•SnapTrackcompatible(orderAltronixmodel#ST3)
•DINRailMountversionavailable
(orderAltronixmodel#DTMR1).
Boarddimensions:3”Lx2.5”Wx.75”H(approximate)
Termékspecifikációk
| Márka: | Altronix |
| Kategória: | nincs kategorizálva |
| Modell: | 6062 |
Szüksége van segítségre?
Ha segítségre van szüksége Altronix 6062, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Altronix
27 Augusztus 2024
27 Augusztus 2024
27 Augusztus 2024
27 Augusztus 2024
27 Augusztus 2024
26 Május 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Nutrichef
- nincs kategorizálva Saturn
- nincs kategorizálva Bavaria
- nincs kategorizálva Gustard
- nincs kategorizálva Keurig
- nincs kategorizálva Andover
- nincs kategorizálva Britax-Römer
- nincs kategorizálva Multibrackets
- nincs kategorizálva Sylvania
- nincs kategorizálva Dimplex
- nincs kategorizálva Namco Bandai Games
- nincs kategorizálva PowerPlus
- nincs kategorizálva Topcraft
- nincs kategorizálva Majestic
- nincs kategorizálva Barska
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025