Használati útmutató Argon BASS12

Argon mélynyomó BASS12

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Argon BASS12 (5 oldal) a mélynyomó kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/5
w w w . a r g o n a u d i o . c o m 1
BASS 12 & 15
01 OWNER’S MANUAL
04 ILLUSTRATIONS
05 SPECIFICATIONS
05 TROUBLESHOOT
Owner ’s manual
Dear Customer,
Quality has always been our driving force and
founding Argon Audio is a natural extension of
this philosophy.
We have 20 years’ experience in creating and
specifying high quality products,
manufacturing them and selling them on to
end users with Value Money as the -for-
primary aim. And Argon Audio is a brand fully
compliant with these values.
Design, features and quality standards are all
specified in Denmark and manufacturing takes
place in the Far East, where quality vendors
are highly competitive and as a result supply -
outstanding Value Money products- -for
– to the delight of both ourselves and our
customers!
Introduction
Thank you for choosing Argon Audio
Subwoofer, we hope will bring you many it
years of enjoyment.
Please read this manual fully before
unpacking and installing the product.
Argon BASS -12/15 is manufactures with a no
nonsense approach. is without BASS 12/15
any unnecessary gimmicks, bling bling or
fancy features. The money is spent on quality
components, efficient woofer driver and
extremely solid cabinet. Quality features you
only see on products twice the price of an
Argon BASS . 12/15
Unpacking
We have during production and packing
carefully this checked and inspected
Subwoofer.
After unpacking please check for any damage
from t ransport. We recommend that you keep
the original carton box and packing material
for any future shipping.
w w w . a r g o n a u d i o . c o m 2
BASS 12 & 15
Subwoofer installation
The Subwoofer requires connection to the
mains power supply, so for your safety it is
important that you read both this manual and
the amplifier manual before connecting.
Subwoofer positioning
Variations in placement of loudspeakers can
produce dramatic differences in the way music
sounds. No listening room is the same and
therefore we encourage you to spend some
time experimenting with which placements
work best in your listening room. Positioning
of Subwoofers is however less critical
compared with full-range loudspeakers
because the low frequencies reproduced by a
subwoofer can be difficult to locate in the
room. You can start with our basic
recommendations.
To begin with, if you use the Subwoofer in a
surround set the S-up, ubwoofer should ideally
be positioned between the TV and one of your
front loudspeakers, as fig. 2 to 4 on page 5. If
you are using the Subwoofer in a stereo set-
up the Subwoofer should ideally be positioned
between the two front stereo speakers, as
fig.1on page 5.
You should know that, if the Subwoofer is
placed close to a wall or in a corner, the bass
sound will be enhanced.
It’s your choice what you like the most.
Another example is the placement of the
Subwoofer in the middle of the stereo
speakers or away from the center of the
stereo speakers.
This may have an impact on how you perceive
the stereo image, even though its only low
frequency sounds that come from the
Subwoofer.
Trust your ears and be willing to experiment
freely.
(Almost) everything is possible
Running-in period
We recommend a running-in time of your new
BASS S -12/15 ubwoofer of approximately 15
20 hours at normal listening
level before you decide on the final positioning
and control settings of the Subwoofer . During
the running-in time the drive units will settle in
and perform as intended.
Connecting your Subwoofer
We recommend that you read the manual of
your A receiver carefully before mplifier or AV-
connecting your Subwoofer.
First switch off the Amplifier and all equipment
before you connect the Subwoofer.
Connect your Amplifier/av-reciever’s
SUB OUT-OUT or PRE- to either INPUT
right/left (1 or 2) as shown on page 4.
If you use a Stereo Amplifier it’s
recommended to use the INPUT right/left
connections (1) as shown on page 4.
If you use a AV receiver with a SUB out it’s
recommended to use the LFE connection (2)
on page 4.
When finished, connect the subwoofer power
cable ( as shown on page 9) 4 to the mains
voltage and, push the POWER ON/OFF
button (10 as shown on page ) 4 to ON
position, the indicator lamp POWER LED will
now glow blue and the ubwoofer is active S
and ready to be used.
The Argon ubwoofer has a BASS 12/15 S
built-in AUTO STANDBY function ( 9) as
shown on page 4 and after approximately 20
minutes ignal, without any input s , the
subwoofer will automatically switch off, and
the indicator lamp POWER LED will change
color. When an input signal is detected the
subwoofer will become active and the
indicator lamp POWER LED will glow blue.
Setting volume, frequency and phase
The volume, crossover and phase (controls 4,
5 and 7) as shown on page 4, can be adjusted
on the rear panel, and we recommend that
you adjust the setting of these controls to your
liking – try with different music and films.
w w w . a r g o n a u d i o . c o m 3
BASS 12 & 15
Care and cleaning
We don’t recommend use of any solvents or
cleaners on cabinet, the Argon BASS12/15
cabinet surface usually only requires dusting
or cleaning with a damp soft cloth (only use
cold clean water).
The grille fabric may be cleaned with a normal
clothes brush or vacuumed carefully with the
grille detached from the cabinet. Avoid
touching the drive unit and do not use the,
Subwoofer as a coffee or drinks table (risk of
water being spilled into the subwoofer).
Disconnect the Subwoofer from the mains
supply if taken out of use for a longer period.
Environmental information
Argon BASS12/15 Subwoofer complies with
international directives on the Restriction of
Hazardous Substances Electrical and
Electronic Equipment (WEEE) - the crossed
bin symbol indicates compliance and that the
products must be appropriately recycled or
processed in accordance with these
directives. (RoHS) in electrical and electronic
equipment and the disposal of Waste.
Safety instructions
Please store this instruction manual for future
reference.
Do not use this product near water or
moisture. Clean only with a dry cloth. Unplug
this product from the wall outlet before
cleaning. Place the unit on a solid surface. Do
not block any ventilation openings. Do not put
it in a closed bookcase or a cabinet that may
keep air from flowing through its ventilation
openings. Do not install near any heat
sources, such as radiators, heat registers,
stoves or other appliances that produce heat.
Protect the power cord from being walked on
or pinched, particularly at plugs and the point
where they exit from the product. Servicing is
required when the product has been
damaged. Do not attempt to service this
product yours Opening or removing covers elf.
may expose you to dangerous voltages or
other hazards.
Please contact the manufacturer to be
referred to an authorized service center near
you. To prevent risk of fire or electric shock,
avoid over loading wall outlets, extension
cords, or integral convenience receptacles.
Do not let objects or liquids enter the product.
Use proper power sources. Plug the product
into a proper power source, as described in
the operation instructions or as marked on the
product.
Rear panel and connections
01 Right/left Sound input from source or
stereo amplifier.
02 LFE is for connecting a surround sound
amplifier/receiver. (Crossover frequency is
not adjustable).
03 Link connection is for connecting an extra
subwoofer.
04 Subwoofer Volume adjustment.
05 C - . ross over / Frequency adjustment
06 Power On/Off indicator.
07 Phase adjustment.
08 Power mode setting switch
Off: SUB is turned off,
Auto: SUB is in auto standby/start up.
SUB will power up once Music starts
playing, and SUB will turn off automatically
if there is no Music.
ON: the SUB will remain power on
continuously.
09 Power cable connection.
The power cable should be pulled from
socket if not used for a longer period.
10 Main power switch
See illustration on page 4 for explanation

Termékspecifikációk

Márka: Argon
Kategória: mélynyomó
Modell: BASS12

Szüksége van segítségre?

Ha segítségre van szüksége Argon BASS12, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók mélynyomó Argon

Argon

Argon BASS12 Útmutató

2 Augusztus 2024
Argon

Argon BASS8 MK2 Útmutató

29 Július 2024
Argon

Argon BASS10 MK2 Útmutató

29 Július 2024
Argon

Argon BASS15 Útmutató

28 Július 2024
Argon

Argon BASS10 Útmutató

10 Július 2024
Argon

Argon BASS8 Útmutató

7 Július 2024

Útmutatók mélynyomó

Legújabb útmutatók mélynyomó

Phase Technology

Phase Technology IW200-II Útmutató

4 Április 2025
Wet Sounds

Wet Sounds ZERO 10 S4 XZ-W Útmutató

2 Április 2025
SoundTube

SoundTube CM1001D Útmutató

2 Április 2025
JL Audio

JL Audio FS108-W5 Útmutató

31 Március 2025
Phase Technology

Phase Technology PL-12p Útmutató

30 Március 2025
ETON

ETON Graphit 8-2 Útmutató

19 Március 2025
ETON

ETON Graphit 8-4 Útmutató

19 Március 2025
ETON

ETON Graphit 10-4 Útmutató

19 Március 2025
ETON

ETON MW 10 FLAT Útmutató

19 Március 2025
ETON

ETON PW 8 Útmutató

19 Március 2025