Használati útmutató Arozzi Arena MOTO
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Arozzi Arena MOTO (22 oldal) a Hivatal kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 6.5 felhasználó értékelte átlagosan 4.7 csillagra
Oldal 1/22
073
®
Designed in Sweden© Arozzi Europe AB. 2024
ARENA MOTO
Operations Manual
Display
Up
Down
Set Memory
Save 1
Save 2
Save 3
Save 4
Up/Down operation
Wake up controller
Position memory
Setting a minimum height
• Press the Up button until you reach your desired height. The operation stops when reaching the
highest possible point.
• Press the Down button until you reach your desired height. The operation stops when reaching the
lowest possible point.
• Short-press Up or Down and the display will show current height and react to further input
• You can save up to four positions corresponding to the save buttons (1, 2, 3, 4). Save the current
position by pressing the M key and then your prefferred save button.
• You can see previously saved positions by short-pressing any save button. The display will then show
the saved height.
• Double click or long press any of the save buttons (1, 2, 3, 4) and the desk will move to the
corresponding position.
• To set the current height as minimum height for the desk, hold down both Down + M buttons until the
display shows ” ” indicating that the minimum height has been stored. Storing a minimum height -do
ensures that the desk never goes below this position.
• To delete the saved minimum height, let the desk run downwards until it stops. Press down again and
the display shows ” ”. Then hold down Down + M buttons until the display shows ” ” indicating -Lo -do
that the stored minimum height has been deleted.
Setting a maximum height
Mechanical reset
0 position reset
Lock and unlock
Error codes
• To set the current height as maximum height for the desk, hold down both Up + M buttons until the
display shows ” ” indicating that the maximum height has been stored. Storing a maximum height -up
ensures that the desk never goes above this position.
• To delete the saved maximum height, let the desk run upwards until it stops. Then press the Up button
again and the display shows ” ”. Then hold down Up + M buttons until the display shows ” ” -hI -up
indicating that the stored maximum height has been deleted.
• Hold down both Up + Down buttons at the same time until the display shows ” ”. Let the desk run. ---
After it has stopped, the reset is complete. This resets maximum height and minimum height.
• Hold down the Down button until the display shows ” ”. The desk will run downwards to recognize ---
the 0 height. It will then move up to its xed position.
• Lock/unlock the controller unit by holding down the M + 4 buttons until the display shows ” ” for L
locked, or returns from ” ” to regular numbers for unlocked.L
* Contact Arozzi support.
EU: arozzi.se/support --- US: arozzi.com/support
Code Description Clear method
E01 Motor A - Not connected Press up / down button -> Check motor A cable
E02 Motor B - Not connected Press up / down button -> Check motor B cable
E03 Motor A - Overcurrent Press up / down button -> Reduce load -> Replace motor A *
E04 Motor B - Overcurrent Press up / down button -> Reduce load -> Replace motor B *
E05 Press up / down button -> Check A cable -> Replace motor A*Motor A - Internal sensor failure
E06 Motor B - Internal sensor failure Press up / down button -> Check B cable -> Replace motor B*
E07 Main power supply problem Unplug the desk. Plug it in again -> Replace power supply *
E08 Motor A - Abnormal current Unplug the desk. Plug it in again -> Replace motor A *
E09 Motor B - Abnormal current Unplug the desk. Plug it in again -> Replace motor B *
E10 Motor A - Power device failure Unplug the desk. Plug it in again -> Replace motor A *
E11 Motor B - Power device failure Unplug the desk. Plug it in again -> Replace motor B *
E12 Position set failure Perform 0 position reset (See above)
E13 Overheat protection Wait for temperature to drop
E14 Motor A - Stalled Press up / down button -> Reduce load -> Replace motor A *
E15 Motor B - Stalled Press up / down button -> Reduce load -> Replace motor B *
E16 Unbalanced position Perform mechanical reset (See above)
E17 Critical data loss Perform mechanical reset (See above)
RST Overload protection Reduce load on desk
© Arozzi Europe AB. 2024
®
Designed in Sweden
Termékspecifikációk
| Márka: | Arozzi |
| Kategória: | Hivatal |
| Modell: | Arena MOTO |
Szüksége van segítségre?
Ha segítségre van szüksége Arozzi Arena MOTO, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Hivatal Arozzi
28 December 2024
2 Szeptember 2024
Útmutatók Hivatal
- Hivatal Insignia
- Hivatal HON
- Hivatal Huzaro
- Hivatal OKA
- Hivatal Cooler Master
- Hivatal Kogan
- Hivatal Tvilum
- Hivatal Livarno Lux
- Hivatal Durable
- Hivatal Aeris
- Hivatal Xtech
- Hivatal FOURZE
- Hivatal Zaor
- Hivatal CoolerMaster
- Hivatal Leen Bakker
Legújabb útmutatók Hivatal
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025