Használati útmutató Audio-Technica AE5100
Oldalak 2 Engels mikrofon
Olvassa el ingyen online a(z) Audio-Technica AE5100 használati útmutatóját, vagy töltse le PDF-ben. Az útmutatót 31 ember találta hasznosnak. Kérdése van a modellről? Tegyen fel kérdést
User Manual
Cardioid Condenser Instrument Microphone AE5100
■Features
■Notes on use
■Connection procedure
This product requires 48 V
DC phantom power.
Outp nsuttermial
PIN1 (ground)
PIN3
(cold)
PIN2 (hot)
■Specifications
Fixed-charge back plate, permanently polarized condenser
Cardioid
20 - 20,000 Hz
80 Hz, 12 dB/octave
-36 dB (15.8 mV) re 1V at 1 Pa
150 ohms
148 dB SPL, 1 kHz at 1% T.H.D.
158 dB SPL, with 10 dB pad (normal)
11 dB SPL
137 dB, 1 kHz at Max SPL
83 dB, 1 kHz at 1 Pa
11-52 V DC, 3.2 mA typical
High-pass filter,
10 dB pad (normal)
Integral 3-pin XLRM-type
•1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
*Typical, A-weighted, using Audio Precision System One.
■Pratternola p
■Fr roeequencyespns
180°
150°
120°
30°
0°
330°
300°
270°
240°
210°
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
05-DEC--2020 Form No.ATGC-L0384-20
LEGEND
0°, 50cm
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
Thank you for purchasing this product. Before using the product, read through the user
manual to ensure that you will use the product correctly.
Please keep this manual for future reference.
The AE5100 is intended for use in professional applications where remote power is available.
It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or
by a separate, in-line source such as the Audio-Technica AT8801 single channel or CP8506
four-channel phantom power supplies.
Output from the microphone’s XLRM-type connector is low impedance (Lo-Z) balanced. The
signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” –
positive acoustic pressure produces positive voltage at Pin 2.
An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a
low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close
vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic,
air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.
The AE5100 includes an AT8471 isolation clamp to provide secure mounting, versatile
positioning, and effective dampening of unwanted mechanical noise.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43°C
for extended periods. Extremely high humidity should also be avoided.
Connect eas a microphone input the output terminals of the microphone to a dvice that h
(balanced input) compatible with a phantom per supply. The output connector is an ow
XLRM-type with polarity as shown in the figure below.
For product improvement, the product is sublect to modification without notice.
• Uncompromising sound quality for overheads, percussion, acoustic guitar, strings and other
acoustic instruments
• Large-diaphragm capsule delivers accurate and natural response
• Low-profile design permits innovative placement options previously unattainable with a
large-diaphragm condenser
• Robust design for enduring dependability on the road
• Integral 80 Hz HPF switch and 10 dB pad
• Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation
of desired sound source
■Safety precaution
■Cautions for the product
Although this product was designed to be used safely, failing to use it correctly may result in
an accident. To ensure safety, observe all warnings and cautions while using the product.
• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a hot, humid or
dusty place.
Element
Polar pattern
Frequency response
Low Frequency response
Open circuit sensitivity
Impedance
Maximum input sound level
Noise
Dynamic range (typical)
Signal-to-noise ratio
Phantom power requirements
Switch
Output connector
Roll-off
143 g
148.5 mm long, 26.0 mm maximun diameter
Weight (less accessories)
Dimensions
Included accessoriesAT8471 isolation clamp for 5/8"-27 threaded stands;
5/8"-27 to 3/8"-16 threaded adapter;
AT8136 windscreen; soft protective pouch
60°
90°
Response in dB
Frequency in Hertz
10
0
-10
-20
-30
20
5001005020010k5k1k 2k20k
10 dB
Termékspecifikációk
| Márka: | Audio-Technica |
| Kategória: | mikrofon |
| Modell: | AE5100 |
Szüksége van segítségre?
Ha segítségre van szüksége Audio-Technica AE5100, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók mikrofon Audio-Technica
Audio-Technica ES945O/FM5 Útmutató Audio-Technica ES933/H Útmutató Audio-Technica ATM410 Útmutató Audio-Technica Freeway ATW-251/G Útmutató Audio-Technica AT4021 Útmutató Audio-Technica BP28L Útmutató Audio-Technica ES935C6 Útmutató Audio-Technica ATR4750-USB Útmutató
Összes Audio-Technica mikrofon használati útmutató
Népszerű termékek – mikrofon
Audio-Technica AT882TH/DS3RC5 Útmutató Audio-Technica ATM-650 Útmutató Audio-Technica ATM610a Útmutató