Használati útmutató Blaupunkt IRC-S2

Blaupunkt Térfigyelő kamera IRC-S2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Blaupunkt IRC-S2 (2 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Wireless PIR Camera (IRC-S2)
P
Pa
ar
rt
ts
s
D
De
es
sc
cr
ri
ip
pt
ti
io
on
n
1. Blue LED /Learn Button
2. IR Sensor
3. LED Flash
T LED Flash delivers sufficient light for image capture in low he
lighting condition .
4. PIR Camera Lens
5. Battery Insula tor
Pull out the insulator to activate battery.
6. Bottom Screw (Tamper Switch)
The Tamper switch protects the PIR Camera from unauthorized
cover opening and is depressed by bottom screw. When the
screw is loosened, the tamper switch will be activate.
PPaacckkaaggee CCoonntteenntt
1 x PIR Camera
4 x wall plugs and screws
2 1.5V AA alkaline batteries (Pre-inserted) x
The PIR Camera can only be learnt into Control Panel within 3
minutes after powering on. If it has been powered on for more
than 3 minutes, remove and reinsert batteries to repower on the
PIR Camera.
1. Put the Control Panel into learning mode l.
2. Press and hold the learn button PIR Camera for 10 on
seconds until both LED Flash and Blue LED flash once, then
release the button to transmi learn code. t a
3. Wait for a short time for PIR Camera to connect to panel. If the
camera is successfully learnt in, the Blue LED will flash twice
to indicate. The panel will also display PIR Camera info. Refer
to panel manual to complete learning.
4. If the PIR Camera and Control do not respond after a short
time (about 20~30 seconds), restart from step 2 to press and
hold the button again.
After learning has been completed, Do press and hold the NOT
learn button for 10 seconds again within 3 minutes after power on,
otherwise the PIR Camera will disconnect from panel and must
be relearnt again.
M
Mo
ou
un
nt
ti
in
ng
g
T PIR camera designed to be mounted on either a flat surface he
or in a corner with fixing screws and plugs provided.
The base has knockouts where the plastic is thinner and can be
broken through for mounting. 2 in the center for surface
mounting and 4 on the sides for corner mounting.
1. Remove the cover.
2. For surface mounting, break through the knockouts at t 2 he
center of base.
For corner mounting, break through the 4 knocks on the
corner of PIR camera
3. e the holes as template Us to drill holes in the wall.
4. Insert the wall plugs if fixing it into plaster or brick.
5. Screw the base into the wall plugs.
6. Screw the cover back onto its base.
MMoottiioonn DDeetteeccttiioonn
The PIR Camera is designed to detect movement in protected
area. Upon movement detection, the PIR reports to the Control
Panel for an alarm activation captures 3 images at the same and
time. The images are transferred to the Control Panel to send to
programmed destinations for user to view.
W
Wa
ar
rm
m
U
Up
p
P
Pe
er
ri
io
od
d
When the Control Panel enters arm mode, or PIR Camera is put
into Test Mode, the PIR Camera will warm up for 30 seconds. Do
not trigger the PIR Camera during the 30 seconds warm up
period. If the PIR Camera is under low battery or tamper opened
condition, the Blue LED will light up during the warm up period.
BBaatttteerryy
The PIR Camera uses two 1.5V AA Alkaline batteries as its power
source. Remove the battery insulator to activate battery. It also
features low battery detection function to notify the Control Panel
when battery voltage is low.
When the PIR camera is low battery, follow the procedure on
below to change the batteries.
1. Open the PIR camera back cover.
2. Remove the old batteries.
3. Press the tamper switch several times to fully discharge.
4. Insert the new batteries and replace the PIR Camera back
cover.
L
Le
ea
ar
rn
ni
in
ng
g
OOppeerraattiioonn
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
Surface Fixing
Knockouts x 2
Corner Fixing
Knockouts x 4
Battery Saving Guideline
The PIR Camera is wirelessly connected with the Control Panel at
a time. When the PIR Camera loses connection with the Control ll
Panel, it will actively search for the Control Panel, which will
consume extra power and greatly reduces battery life. In order to
avoid unnecessary power consumption, please follow the
guidelines below:
1. Ensure the Control Panel is powered on before removing the
battery insulator. Always learn in the PIR Camera immediately
after activating the battery.
2. Ensure the Control Panel is powered on and within signal
range when the PIR Camera is powered on.
3. When you removed the PIR Camera from the Control Panel,
make sure to remove the batteries from the PIR Camera too.
T
Te
es
st
t
M
Mo
od
de
e
The test mode function allows you to check the PIR camera’s
detection range. Press and hold the button over 3 seconds, Learn
then release the button to enter the Test mode for 5 minutes.
The PIR Camera will first warm up for 30 seconds, do not trigger
the PIR camera during this warm up period. After the warm up is
complete, you could trigger PIR camera to check its detection
range. PIR camera is triggered, the Blue LED will light up to If
indicate.
For signal range test, please refer to the control panel manual.
L
LE
ED
D
I
In
nd
di
ic
ca
at
to
or
r
Off
Normal Operation
On (2 seconds)
Movement detection under low battery,
tamper triggered condition, or Test mode.
On (30 seconds)
PIR Camera is warming up under low
battery or tamper triggered condition
Flash Rapidly
PIR Camera is transferring image under
low battery or tamper triggered condition.
Flash Once
PIR Camera sends a learn code
Flash Twice
PIR Camera is learnt into Control Panel
Flash every 20
minutes
PIR Camera has lost signal connection
with the Control Panel.
E
En
nv
vi
ir
ro
on
nm
me
en
nt
ta
al
l
C
Co
on
nd
di
it
ti
io
on
n
- C to 40 C, relative humidity 85% non-condensing 10° ° .
R
Ra
ad
di
io
o
2.4 GHz
S
Sp
pe
ec
ci
if
fi
ic
ca
at
ti
io
on
n

Termékspecifikációk

Márka: Blaupunkt
Kategória: Térfigyelő kamera
Modell: IRC-S2

Szüksége van segítségre?

Ha segítségre van szüksége Blaupunkt IRC-S2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Térfigyelő kamera Blaupunkt

Blaupunkt

Blaupunkt DC-S3 Útmutató

4 Október 2024
Blaupunkt

Blaupunkt PB-S1 Útmutató

3 Október 2024
Blaupunkt

Blaupunkt KPT-S1 Útmutató

18 Szeptember 2024
Blaupunkt

Blaupunkt KP-S1 Útmutató

2 Augusztus 2024
Blaupunkt

Blaupunkt VIO-D40 Útmutató

1 Augusztus 2024
Blaupunkt

Blaupunkt BX-S1 Útmutató

31 Július 2024
Blaupunkt

Blaupunkt IRP-S1L Útmutató

30 Július 2024
Blaupunkt

Blaupunkt TS-S1 Útmutató

28 Július 2024
Blaupunkt

Blaupunkt RC-S1 Útmutató

25 Július 2024
Blaupunkt

Blaupunkt RC-S3 Útmutató

24 Július 2024

Útmutatók Térfigyelő kamera

Legújabb útmutatók Térfigyelő kamera

Hikvision

Hikvision DS-2CE10DF8T-FSLN Útmutató

6 Április 2025
Hikvision

Hikvision DS-2CE56C0T-IRPF Útmutató

5 Április 2025
Hikvision

Hikvision DS-2CD2141G1 Útmutató

5 Április 2025
Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Útmutató

15 Január 2025
Toshiba

Toshiba IKS-WR7412 Útmutató

14 Január 2025
Flir

Flir FC-610 O Útmutató

13 Január 2025
AVerMedia

AVerMedia FC1320-P Útmutató

13 Január 2025
Digitus

Digitus OptiMax DN-16037 Útmutató

13 Január 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Útmutató

13 Január 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Útmutató

13 Január 2025