Használati útmutató Byron BY212
Byron
Ajtócsengő
BY212
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Byron BY212 (3 oldal) a Ajtócsengő kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.1 csillagra
Oldal 1/3
To select the Chime Volume level, press the ‘VOL’
button on the chime There are 4 selectable volume
levels, the Door Chime is pre-set to the loudest
volume setting.
Volume
Default
Functions:
ON
1: plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
1: plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
3: Chime will ‘Beep’ on Start
4
™Plug-in & Portable
Wire Free Chime Kit
1:
2:
4:
:3
7:
5:
BY212
1: Push Button 5: Portable Chime
2: Melody Selector 6: Speaker
3: Bell Push Battery 7: Volume control
4: Signal Sent LED 8: Plug-in Chime
ON
6: 6:
8:
7:
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push
2: Gently twist
3: The backing plate will unclip
1
31: Remove the battery cover of
the Door Chime.
2: Insert 3 X 1.5V Size ‘AA’
batteries (Not Supplied).
3: Make sure the
Positive/Negative terminals
match the internal markings.
4: Chime will ‘Beep’ on Start up.
5: Replace the battery cover
3 x 1.5V ‘AA’
6 Selectable Melodies
1: Tubular 3-Note 4: Solo
2: Big Ben 5: Tubular Score
3: Tubular 2-Note 6: Clarinet
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push
2: Press the Melody Select button.
3:The chime will play the newly selected
sound
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
CR2032
1: Press and hold the ‘VOL’
buttons on both Door
Chimes, until the Chimes
‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chimes.
3: The Chimes will ring to
confirm setup, wait 60
seconds for the Chimes
to exit the learn mode
before repressing the Bell
Push.
5
Beep
Beep
Beep
Beep
New Chime
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Press and hold the ‘VOL’ button on your New Door Chime, until the
Chime goes ‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within 60 seconds to learn the additional
Chime to the Bell Push.
3: Chime will ring to confirm setup, wait 60 seconds for the Chime to
exit the learn mode before repressing the bell push.
Adding Additional Chime/Bell Push:
Beep
Beep
Additional Bell Push
To add an additional Bell Push to the Door
Chime kit
1: Press and hold the ‘VOL’ button on your
Door Chime, until the Chime goes
‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within 60 seconds
to learn the additional Bell Push to the
Chime
3: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the bell push.
For Front/back door setup, select a different melody in one of
the Bell Pushes - .See Melody Selection
Note: Maximum of 6 Bell Pushes can be learnt to a single Chime
Front Door
Back Door
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
Termékspecifikációk
| Márka: | Byron |
| Kategória: | Ajtócsengő |
| Modell: | BY212 |
Szüksége van segítségre?
Ha segítségre van szüksége Byron BY212, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Ajtócsengő Byron
8 Október 2024
5 Október 2024
5 Október 2024
4 Október 2024
1 Október 2024
30 Szeptember 2024
29 Szeptember 2024
27 Szeptember 2024
24 Szeptember 2024
23 Szeptember 2024
Útmutatók Ajtócsengő
Legújabb útmutatók Ajtócsengő
30 Március 2025
30 Március 2025
30 Március 2025
30 Március 2025
16 Január 2025
10 Január 2025
8 Január 2025
2 Január 2025
31 December 2025
31 December 2025