Használati útmutató Chamberlain 041-0136

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chamberlain 041-0136 (8 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 9 felhasználó értékelte átlagosan 4.4 csillagra

SAFETY REVERSING SENSOR REPLACEMENT

041-0136 & 041-0155

BesurepowerisNOT connected to thegaragedooropenerBEFORE installing the

safetyreversing sensor.

TopreventSERIOUSINJURYorDEATHfromclosing garagedoor:

•Correctlyconnectand align thesafetyreversing sensor.Thisrequired safety

deviceMUSTNOT bedisabled.

•Install thesafetyreversing sensorsobeam isNOHIGHERthan 6"(15 cm)

abovegarage floor.

WARNING: Thisproduct canexposeyou to chemicalsincluding lead,whichare

known to the StateofCaliforniato causecancerorbirth defectsorother

reproductiveharm. Formoreinformation go towww.P65Warnings.ca.gov

Theimages throughoutthismanualare for reference only andyour product may look

different.

INSTALL THE SAFETY REVERSING SENSORS

Disconnectpowertothe garage dooropenerbeforeyou begin.

The safetyreversing sensorsaredesignedtoclip onto thedoortrackwith theprovided

sensorbrackets.Ifthedoortrackwill notsupportthesensorbracketawall installation is

recommended.The sensorbeam should be NOHIGHERthan 6"(15 cm)abovethefloor.

DOOR TRACKINSTALLATION

1.Slide the curvedarms ofthe sensor bracket aroundthe edgeofthe doortrack.

Snap into placesothatthesensorbracketisflush againstthetrack.

2.Slide the hex screwthroughthesensor.

3.Attach thesensortothe bracketwith thewing nut. Makesurethelensisnot

obstructed bythebracket.

Repeatthesteps with theothersensoron theoppositedoortrack.Both lensesmust

faceeach other.

6" (15 cm) max.

Door track

1

2 3

Garage door

Wing nut

WALL OPTION

Make sure thebrackets oneachsideare clearofthedoor track andhave the same

amount ofclearancesothesensorswill align correctly.Ifadditionalclearanceisneeded,

useextension brackets041A5281-1 (not provided)orwood blocks.

1.Attach thesensorbracketagainst thewall with two lagscrews(not provided).

2.Slide the hex screwthroughthesensor.

3.Attach thesensortothe bracketwith thewing nut. Makesurethelensisnot

obstructed bythebracket.

Repeat the stepswiththeothersensor onthe opposite side ofthegarage door. Both

lensesmust faceeach other.

OR

1

Wing Nut

OPTIONAL

2 3

Door track

Inside

garage wall

6" (15 cm)

max.

Not provided

FLOOR OPTION

1.Measure the positionofbothsensor brackets sothey willbe the samedistance

from thewallandunobstructed.

2.Attachthe brackettothefloorwithconcrete anchors (notprovided).

3.Slide the hex screwthroughthesensor.

4.Attach thesensortothe bracketwith thewing nut. Makesurethelensisnot

obstructed bythebracket.

Repeat the stepswiththeothersensor onthe opposite side ofthegarage door. Both

lensesmust faceeach other.

1

3 4

2

Inside

garage wall

Not provided

Door track

6" (15 cm) max.

Wingnut

Termékspecifikációk