Használati útmutató Chief HB29S
Oldalak 2 Engels Lapos panel támogatás
Olvassa el ingyen online a(z) Chief HB29S használati útmutatóját, vagy töltse le PDF-ben. Az útmutatót 21 ember találta hasznosnak. Kérdése van a modellről? Tegyen fel kérdést
INSTALLATION INSTRUCTIONS
Continued...
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F: 877.894.6918 / 952.894.6918
8803-000120
©2008 Milestone AV Technologies
9/30/08
MODEL: HB-29S Custom Projector Bracket
Unpack carton and verify contents. If any listed parts are miss by calling ing, immediately contact a Chief Customer Service representative
1-800-582-6480.
PARTS
Figure 1:
INSTALLATION
WARNING:
IMPROPER INSTALLATION MAY RESULT IN SERIOUS PERSONAL INJURY! All components must be securely fastened
to each other and to the ceiling, and the ceiling must be capable of supporting five times the total weight of the installation.
CAUTION:
This HB bracket mount is designed to support the weight of only one projector per mount. DO NOT attempt to attach more
than one projector to the same mount!
1.Place custom HB bracket on underside of the projector and line up the four screw holes on the bracket with the four corresponding holes
on the projector. Ensure that the side hooks open towards back of the projector. (See Figure 1)
2.Attach HB bracket to projector using four M6-1.00 x 16mm Phillips machine screws through washers and spacers into projector. Install
each screw partially to make sure all screws are aligned correctly before tightening the screws to the bracket. (See Figure 1)
(1) BRACKET, Custom HB(4) NUT, Flange, Hex, 5/16-18
(4) SCREW, Phillips Machine, M6-1.00 x
16mm
(4) FLAT WASHER, Standard Machine
Screw 6mm
1
2
x 4
Toward front
of projector
Termékspecifikációk
| Márka: | Chief |
| Kategória: | Lapos panel támogatás |
| Modell: | HB29S |
Szüksége van segítségre?
Ha segítségre van szüksége Chief HB29S, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Lapos panel támogatás Chief
Chief FDP4100B Útmutató Chief OFB131 Útmutató Chief RPMA196 Útmutató Chief FSB4101S Útmutató Chief PSM2042 Útmutató Chief FCA515 Útmutató Chief PCM2176 Útmutató Chief MSS6200S Útmutató
Összes Chief Lapos panel támogatás használati útmutató
Népszerű termékek – Lapos panel támogatás
Útmutatók Lapos panel támogatás
Legújabb útmutatók Lapos panel támogatás
Peerless-AV ACC-VCS Útmutató Peerless-AV DS-LEDTK-6S Útmutató NeoMounts AWL75-450BL Útmutató NeoMounts NM-D135DBLACK Útmutató NeoMounts FPMA-D700DV Útmutató NeoMounts FPMA-C100WHITE Útmutató NeoMounts FPMA-W830 Útmutató NeoMounts FPMA-DTB200 Útmutató NeoMounts FPMA-D890WHITE Útmutató NeoMounts FPMA-CB100BLACK Útmutató