Használati útmutató Chief RSMA181
Chief
Lapos panel támogatás
RSMA181
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief RSMA181 (1 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 13 ember találta hasznosnak és 7 felhasználó értékelte átlagosan 4.8 csillagra
Oldal 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000248 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-181, SSM-181, SLB-181 and SLM-181 Interface Brackets
SSB-181, SSM-181, SLB-181 and SLM-181 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the .500" nylon spacers over the threaded inserts in the bottom of the projector
4. Place the interface bracket onto nylon spacers in the bottom of the projector and align the holes in the bracket with the threaded inserts in
the bottom of the projector.
5. Using the M4 x 20mm mounting screws, position mounting screws into the mounting holes. Tighten all fasteners at this time, securing the
bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions
in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (2) Screw, Phillips Flat Head, M4 x 20mm
(6) 10-24 Thumb Nuts ** (2) Screw, Phillips Pan Head, M4 x 20mm
(1) All-Points Security Kit (2) Washers, Flat, M4
(4) Spacer, Nylon, .500 x .194 x .500
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-181 SLM-181
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interface
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector
Termékspecifikációk
| Márka: | Chief |
| Kategória: | Lapos panel támogatás |
| Modell: | RSMA181 |
Szüksége van segítségre?
Ha segítségre van szüksége Chief RSMA181, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Lapos panel támogatás Chief
3 Április 2025
3 Április 2025
3 Április 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
29 December 2024
29 December 2024
Útmutatók Lapos panel támogatás
- Lapos panel támogatás Panduit
- Lapos panel támogatás NEC
- Lapos panel támogatás Planar
- Lapos panel támogatás Nabo
- Lapos panel támogatás Barkan
- Lapos panel támogatás Cabstone
- Lapos panel támogatás ViewZ
- Lapos panel támogatás Bell'O
- Lapos panel támogatás Metronic
- Lapos panel támogatás Insignia
- Lapos panel támogatás 3M
- Lapos panel támogatás Anthro
- Lapos panel támogatás Digitus
- Lapos panel támogatás BakkerElkhuizen
- Lapos panel támogatás My Wall
Legújabb útmutatók Lapos panel támogatás
8 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025