Használati útmutató Chief SLB620
Chief
Lapos panel támogatás
SLB620
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief SLB620 (1 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 5 felhasználó értékelte átlagosan 4.4 csillagra
Oldal 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone
makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation
or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, ex-
pressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this
document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000189 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-620, SSM-620, SLB-620 and SLM-620 Interface Brackets
SSB-620, SSM-620, SLB-620 and SLM-620 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector and align the holes in the bracket with the threaded inserts in the bottom of the
projector.
4. Using the M4 x 10mm mounting screws and washers, position screws with washers into the mounting holes. Tighten all fasteners at this
time securing the bracket to the projector.
NOTE: Security Screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M4 x 10mm
(4) 10 - 24 Thumb Nuts** (4) Washer, Flat, M4
(1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-620 SLM-620
Towards front of
projector
Towards front of
projector
(
Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSM-style interface bracket connection
s
are encircled)
Termékspecifikációk
| Márka: | Chief |
| Kategória: | Lapos panel támogatás |
| Modell: | SLB620 |
Szüksége van segítségre?
Ha segítségre van szüksége Chief SLB620, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Lapos panel támogatás Chief
3 Április 2025
3 Április 2025
3 Április 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
16 Január 2025
29 December 2024
29 December 2024
Útmutatók Lapos panel támogatás
- Lapos panel támogatás Iiyama
- Lapos panel támogatás Hitachi
- Lapos panel támogatás Pyle
- Lapos panel támogatás One For All
- Lapos panel támogatás Ultimate
- Lapos panel támogatás Konig
- Lapos panel támogatás Helder
- Lapos panel támogatás Erard
- Lapos panel támogatás Mount-It!
- Lapos panel támogatás Newstar
- Lapos panel támogatás Kondator
- Lapos panel támogatás Manhattan
- Lapos panel támogatás Bell'O
- Lapos panel támogatás CTA Digital
- Lapos panel támogatás Vision
Legújabb útmutatók Lapos panel támogatás
8 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025
3 Április 2025