Használati útmutató Chief SLM208
Chief
Projektor tartozék
SLM208
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief SLM208 (1 oldal) a Projektor tartozék kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 4 felhasználó értékelte átlagosan 4.8 csillagra
Oldal 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000274
10/18/07
SLB-208 and SLM-208 Interface Brackets
for BENQ SP830, SP831
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector lining up the four holes in the bracket with the four threaded inserts in the bottom
of the projector.
4. Using the four M4 X 10mm mounting screws and washers, start them into the mounting holes by hand and secure all four fasteners at this
time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (4) WASHER, Flat, M4
(4) 10-24 Thumb Nuts ** (4) SCREW, Pan Head, M4 x 10mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
SLB-208
SLM-208
Towards front of Towards front of
Projector
Projector
Termékspecifikációk
| Márka: | Chief |
| Kategória: | Projektor tartozék |
| Modell: | SLM208 |
Szüksége van segítségre?
Ha segítségre van szüksége Chief SLM208, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Projektor tartozék Chief
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
1 Január 2025
Útmutatók Projektor tartozék
- Projektor tartozék My Wall
- Projektor tartozék Casio
- Projektor tartozék SMK-Link
- Projektor tartozék Optoma
- Projektor tartozék Kingpin Screens
- Projektor tartozék Tempest
- Projektor tartozék Metronic
- Projektor tartozék Omnitronic
- Projektor tartozék Premier Mounts
- Projektor tartozék Nedis
- Projektor tartozék NeoMounts
- Projektor tartozék Peerless-AV
- Projektor tartozék Unicol
- Projektor tartozék Newstar
- Projektor tartozék Sony
Legújabb útmutatók Projektor tartozék
27 Március 2025
27 Március 2025
14 Január 2025
10 Január 2025
7 Január 2025
27 December 2024
27 December 2024
23 December 2024
23 December 2024
23 December 2024