Használati útmutató Chord SPM 1400 Mk2

Chord Vevő SPM 1400 Mk2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chord SPM 1400 Mk2 (5 oldal) a Vevő kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/5
SPM 1400 MK2
POWER AMPLIFIER MANUAL
OPERATING INSTRUCTIONS
INSTALLATION
Your amplier should be positioned to ensure a free ow of air over the rear heat sink and through the upper and
lower grilles. When driven continuously at well above average listening levels, the temperature on the heat sink may
exceed 50oC. This is not a fault, but an indication of the need for adequate ventilation.
Please ensure that the IEC mains lead is correctly terminated.
UK/EUROPE Brown = LIVE = Black USA/CANADA
Blue = NEUTRAL = White
Yellow/Green = EARTH = Green
THE SPM 1400 Mk 2 MUST BE EARTHED AT ALL TIMES VIA ITS OWN MAINS LEAD.
FAILURE TO DO THIS MAY BE HAZARDOUS.
CE This unit complies with EN 50081-1 & IEC 801/2
It has come to light that, in some European
countries a hum may occur if Pre and Power
Ampliers are connected to mains wall sockets
which do not have an earth. Please ensure
that, if this is the case, the pre and power amps
are connected via a multi-way mains block
which contains an earth point at each socket
outlet. This is to ensure that the chassis
metalwork of each item is connected together
and Chord Electronics Limited rmly
recommends that an earthing method for the
building is implemented.
REAR PANEL
The rear of the SPM 1400 Mk 2 has two sets of inputs, one set of balanced XLR connections and one set of phono
RCA connectors. You will also notice by looking at the diagram below that the inputs can be connected as either
INVERTING or NON-INVERTING modes. Connecting to either the phono or the XLR on the right hand side will
give an inverted output as is normal with other Chord amplication. However if a non-inverting output is preferred
simply connect to the left hand side.
As the SPM 1400 Mk 2 is of mono block construction only one of the inputs should be used. Where a pair of units is
used for stereo operation the user should take care to connect both ampliers in the same manner so as not to have an
out of phase configuration. The input should be connected last, with the amplier switched o.
There are two sets of high current gold plated output terminals, the speaker may be connected to either the left or the
right set of terminals. For Bi-wiring conguration both sets of outputs can be used.

Termékspecifikációk

Márka: Chord
Kategória: Vevő
Modell: SPM 1400 Mk2

Szüksége van segítségre?

Ha segítségre van szüksége Chord SPM 1400 Mk2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Vevő Chord

Chord

Chord Anni Útmutató

14 Október 2024
Chord

Chord Hugo TT 2 Útmutató

10 Szeptember 2024
Chord

Chord CPA 2500 Útmutató

3 Szeptember 2024
Chord

Chord Qute HD Útmutató

28 Augusztus 2024
Chord

Chord CB-15BT Útmutató

26 Augusztus 2024
Chord

Chord CA-15BT Útmutató

26 Augusztus 2024
Chord

Chord CG-10BT Útmutató

26 Augusztus 2024
Chord

Chord Ultima 3 Útmutató

20 Augusztus 2024
Chord

Chord BLU MKII Útmutató

18 Augusztus 2024
Chord

Chord CPA 5000 Útmutató

9 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő