Használati útmutató Crestron BPCI-8

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Crestron BPCI-8 (20 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 16 ember találta hasznosnak és 8 felhasználó értékelte átlagosan 4.6 csillagra

DOGUIDE

1. Remove the faceplate by snapping it off the button assembly.

NOTE: Use care when removing the faceplate, as it holds the button support grid and

button caps in place.

2. Ensure the button unit is oriented with the arrow at the top, and then insert the unit into the

electrical box and attach it using the supplied #6-32 x 1" screws.

3. Return the button caps to their original positions on the button assembly with LED windows

oriented upward to match each LED indicator.

4. Install the button support grid with stabilizing tabs to the rear, put the faceplate in position

(optical cable access port on the lower right), and snap it into place.

Mount the BPC-8-IMC

Mount the BPC-8-IMC onto an appropriate surface at the display location using the supplied

hook and loop tape.

DO Connect the Device

Make connections to the BPC-8 using Crestron® power supplies for Crestron equipment. Apply

power after all connections have been made.

Connect the BPC-8

BPC(I)-8

onCue® Basic Presentation Controller

DO Install the Device

NOTE: The BPC-8 and BPCI-8 are functionally similar. For simplicity within this guide, the term

“BPC-8” is used except where noted.

The hardware supplied with the BPC-8 is listed in the DO Check the Box table.

The following tools are required for installation of a BPC-8:

1. Phillips screwdriver (not included)

2. Two #6-32 x 1" pan head Phillips screws (included)

3. Two 4-pin detachable terminal block connectors (included)

Install a Conductor Cable

Install a 4-conductor cable (minimum 24 AWG) with 50ft (~15m) maximum length (not included)

between a 1-gang electrical box for the BPC-8 and the location of the BMP-8-IMC interface

module.

Refer to the pin connections shown in the installation diagram below and connect the supplied

4-pin detachable connectors to each end of the cable.

Mount the BPC-8 into an Electrical Box

Connect the preinstalled cable to the 4-pin terminal block on the rear of the button assembly,

and then mount the BPC-8 to a 1-gang electrical box as shown in the following diagram.

DO Check the Box

QTYPRODUCTCOLORPART NUM.

1Button Assembly4512112

1Module, Interface4511874

1Emitter Probe, IR, Crestron STRIPBlack2001137

1Fastener, Dual Lock, 2.5" x 1"2005414

2Connector, 4-Pin2003576

2Screw, 6-32 x 1", Pan Head, Phillips2007251

BPC-8 Only

1Power Pack, 12 Vdc 0.5 A, 100-240 Vac2045853

BPCI-8 Only

1Power Pack, 12 Vdc 0.5 A, 120-240 Vac2045884

1Bracket, Mounting, Single Gang2030802

LED window

Button assembly

1-gang electrical box

(2.5 in (~63 mm) depth

recommended)

Interchangeable

button caps

Button support

grid

6-32x1”

pan head screws

Optical cable access port

CBL-PWR-CTRL-P-TL-50

cable or equivalent

Grid stabilizing tabs

LED

indicators

BPC- 8-IMC

12T R G

12: Power (12 Vdc)

T: Data

R : Data

G: Ground

Faceplate

B PC-8-IMC

12 T R G

Access port: For optical cable from BPC-HLPIR

IR learner and programmer (optional)

BPC-8-IMC:Power and control signals to/from

BPC-8-IMC interface module (included)

Termékspecifikációk