Használati útmutató Crestron CBLR2-USB
Crestron
nincs kategorizálva
CBLR2-USB
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Crestron CBLR2-USB (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 13 ember találta hasznosnak és 7 felhasználó értékelte átlagosan 4.3 csillagra
Oldal 1/2
DO GUIDE
CBLR2 Series
Cable Retractors for FlipTopsTM
DO Prepare the FlipTop
Preparation of the Crestron® FlipTop™ consists of the following:
• Modifying the FlipTop assembly to accommodate the cable retractors
• Determining the desired mounting orientation (Retractors are shipped congured for vertical
orientation, but are easily recongured for horizontal orientation.)
NOTE: The CBLR2-DP-V and CBLR2-DP-H models are dedicated to vertical and horizontal
orientation, respectively.
NOTE: For preparation of the FlipTop 600 Series models, refer to “Modify the FlipTop (FlipTop 600
Series Models).”
Modify the FlipTop (Excludes FlipTop 600 Series Models)
1. Remove four screws (A) to detach the lower bar assembly. Also remove two screws (B). Retain
screws A and B to attach the FlipTop mounting bracket assembly. Refer to the FlipTop mounting
brackets table provided in the “DO Check the Accessories” section on the next page to ensure
that the mounting bracket received is appropriate for the FlipTop being modied.
2. Remove four screws (C) to detach the cable guide. Retain the screws to attach the two side ller
plates (sold separately).
3. Move the mounting bracket assembly up into position and secure it using four screws (A) and two
screws (B) removed in step 1.
4. Position the side ller plates and secure them using four screws (C).
Modify the FlipTop (FlipTop 600 Series Models)
Retractors can be installed in both the left and right sides of the FlipTop 600 Series models.
1. Remove the screw (C) holding the cable guide in place, and then remove the cable guide.
2. Remove the screws (D) holding the cable pass-through bracket in place, and then remove the
cable pass-through bracket.
3. Remove the shoulder screws from the front of the unit. Save these as they are used in retractor
installation.
Recongure the Retractors for Horizontal Operation
NOTE: The CBLR2-DP-V and CBLR2-DP-H models are dedicated to vertical and horizontal
orientation, respectively.
To recongure the retractors for horizontal orientation, refer to the following illustrations and perform
these steps:
1. Remove the four screws (E), two from each side of the retractor, that attach the neck in the vertical
orientation.
2. Reposition the neck as shown in the horizontal orientation view and attach it using the four screws
(E) to secure the neck in that position.
DO Adjust the Retractor
Once the retractor arm conguration is set, refer to the following illustration and adjust the retractor
arm tension and cable retraction speed as follows:
1. Adjust the retractor tension by loosening the top thumb screw enough to enable pulling or pushing
of the adjacent cable end. Align the red screw with the label arrow.
2. Adjust the cable retraction speed.
a. Pull the knob outward and move it to the VERT or HORZ position to match the conguration
of the retractor arms.
b. Pull the cable (plug end) out so it is fully extended.
c. Pull the cable a second time to cause it to retract, and observe the speed of the cable
retraction. If it is too slow or too fast, reposition the knob to an intermediate position and
recheck.
Mounting
Bracket
Assembly
Side Filler Plates
(4) Screws (E)
(Two on Each Side)
Side View
Retractor Neck
(4) Screws (E)
(Two on Each Side)
Side View
Retractor Neck
Thumb Screw
Cable End
HORZ
VERT
Knob
Red Screw
Once installed, use the top thumb screw
to adjust the cable length until the red
screw is aligned with the arrow.
Cable Retraction
Speed Adjustment Slow Fast
Mounting
Bracket
Assembly
Screws (A)
Screw (B)
Screw (B)
Screws (C)
Side Filler
Plates
Cable Guide
Cable Pass-Through Bracket
Shoulder Screws
Screws (C)
Screws (D)
Lower Bar
Assembly
Cable
Guide
Screws (A)
Screw (B)
Screw (B)
Screws (C)
Termékspecifikációk
| Márka: | Crestron |
| Kategória: | nincs kategorizálva |
| Modell: | CBLR2-USB |
Szüksége van segítségre?
Ha segítségre van szüksége Crestron CBLR2-USB, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Crestron
2 Április 2025
2 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
Útmutatók nincs kategorizálva
- nincs kategorizálva Axor
- nincs kategorizálva Carrier
- nincs kategorizálva OSO
- nincs kategorizálva WarmlyYours
- nincs kategorizálva Kingston Technology
- nincs kategorizálva Kospel
- nincs kategorizálva Genie
- nincs kategorizálva Core SWX
- nincs kategorizálva Ade
- nincs kategorizálva JVC
- nincs kategorizálva Ocean Way Audio
- nincs kategorizálva Wasco
- nincs kategorizálva Navionics
- nincs kategorizálva Total Chef
- nincs kategorizálva Pentacon
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025