Használati útmutató Crestron CLWI-KPLEX-BATT
Crestron
nincs kategorizálva
CLWI-KPLEX-BATT
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Crestron CLWI-KPLEX-BATT (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 7.5 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/2
Crestron Electronics, Inc. Installation Guide - DOC. 7244C
15 Volvo Drive Rockleigh, NJ 07647 (2031641)
Tel: 888.CRESTRON 10.14
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at
1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of
Crestron worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.
First-time users must establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features, and extends the capabilities of the CLWI-KPLEX-BATT,
additional information may be made available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation revision.
Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as
an “Addendum” in the Download column.
WARNING: To avo ock or deid fire, sh , ath turn; off po rc ea use nd power is be ore wer at ci uit br ker or f a test that off f
wiring!
NOTES: Observe the following points.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• This product should be installed by a qualified electrician
Crestron CLWI-KPLEX-BATT
On-Wall Wireless Lighting Keypad, Battery Powered
Installation Guide
As of the date of manufacture, the CLWI-KPLEX-BATT has been tested and found to comply with specifications for
CE marking.
Regulatory Compliance
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cuase harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
(Continued on following page)
INTRODUCTION
The CLWI-KPLEX-BATT is a companion keypad for Crestron
®
CLWI dimmers and switches.
It provides lighting and audio control from more than one location around the home or office
using infiNET EX
®
technology. Recall scenes, dim up and down, and adjust volume using the
customizable button layout.
Specifications
Specifications for the CLWI-KPLEX-BATT are listed in the following table.
CLWI-KPLEX-BATT Specifications
ASSIGN BUTTON FUNCTIONS
The CLWI-KPLEX-BATT button functions are based on the control system’s program.
Refer to the Crestron Studio™ or SIMPL Windows help file for details.
ASSEMBLY
The battery and battery door must be installed before installing the CLWI-KPLEX-BATT.
Refer to the illustration in the “Replace Battery” section on page 2 for details.
1. Remove the screw from the back of the CLWI-KPLEX-BATT; retain it for reinstallation.
2. Insert the battery with the positive (+) side facing out.
3. Secure the battery by installing the battery door with the screw removed in step 1.
CHANGE BUTTON ASSEMBLIESTHE
Follow the procedure below if the button assemblies need to be changed or replaced.
1. Squeeze the sides of the button assembly near the center of the device or, for two or
more button assemblies, press on one side of the button assembly.
2. Remove the button assembly by carefully pulling the button assembly off of the
device. For two or more button assemblies, remove the second button in the same
manner. Refer to the illustrations that follow.
Remove the Button Assembly
CLWI-KPLEX-BATT Physical View (Rear and Side Views)
Controls and Indicators
Two 3-Button Pads
One Split Rocker and
One 3-Button Pad
One 3-Button Pad and
One Split Rocker
One Rocker Two Split Rockers
INSTALLATION
The CLWI-KPLEX-BATT attaches to a bracket that is mounted using double-sided tape or
mounting screws. Refer to the procedures below for mounting instructions.
Stick-On Surface Mounting
The CLWI-KPLEX-BATT can be mounted to the wall using the preinstalled double-sided
tape. Refer to the following procedure for instructions.
1. Remove the release liner of the double-sided tape from the rear of the bracket.
2. Ensure that the arrows on the rear of the device point up and firmly press the bracket
against the wall to ensure adhesion.
3. Place the keypad into the bracket.
Stick-On Surface Mounting
Permanent Mounting
The CLWI-KPLEX-BATT can be mounted to a round or square electrical box using two
mounting screws (supplied). It can also be mounted directly to a flat surface using screws
that are appropriate for the mounting scenario (not supplied).
Mounting screws are installed through the bracket and secure to the round or square
electrical box or flat surface. Ensure that the arrows on the rear of the device point up.
Refer to the following illustration for a typical permanent mount scenario.
Permanent Surface Mounting
PHYSICAL DESCRIPTION
This section provides information on the controls and indicators available on the
CLWI-KPLEX-BATT.
CLWI-KPLEX-BATT Physical View (Front and Side Views)
Double-Sided Tape
# CONTROLS AND
INDICATORS
DESCRIPTION
1 Buttons Configurable for a variety of buttons, refer to the
illustration below for button configurations;
Default button arrangement is two 3-button pads;
Maximum layout contains six buttons
2 LED Indicator LED lights to indicate button press
3 Setup Button Allows setup and configuration of the device:
Join an infiNET EX Network: Tap-tap-tap-press
and hold for 2 to 10 seconds
Verify Communications Status: Tap-tap-tap-press
and hold for less than 2 seconds
Enter Setup Mode: Press and hold for 4 seconds
Secure the bracket to the mounting surface
using the double-sided tape attached to the
bracket.
73 mm
(2.85 in)
73 mm
(2.85 in)
20 mm
(0.76 in)
Secure the bracket to the electrical box or flat
surface using screws appropriate for the
mounting scenario.
* Any infiNET EX device that provides expander functionality effectively extends the range of the wireless
network beyond the initial range of the gateway. Battery-powered infiNET EX devices do not provide
expander functioanality. A dedicated infiNET EX wireless expander, model CLW-EXPEX or GLA-EXPEX
(both sold separately), is also available.
SPECIFICATION DETAILS
Power Requirements 3 volts lithium coin cell battery, 40 mA;
CR2450 battery
Wireless
RF Transceiver infiNET EX 2-way RF, 2.4 GHz ISM Channels 11 to
26 (2400 to 2483.5 MHz), default channel 15;
IEEE 802.15.4 compliant
Range (Typical) 46 m (150 ft) indoor, 76 m (250 ft) outdoor to
nearest mesh network device(s);
Subject to site-specific conditions and individual
device capabilities*
Gateway Requires an infiNET EX gateway (sold separately)
Environmental
Temperature 0° to 40° C (32° to 104° F)
Humidity 10% to 90% RH (non-condensing)
Enclosure Mounts to surface, requires faceplate (not included)
Dimensions
Height 73 mm (2.85 in)
Width 73 mm (2.85 in)
Depth 20 mm (0.76 in) including front face with buttons
Weight 55 g (2 oz)
Termékspecifikációk
| Márka: | Crestron |
| Kategória: | nincs kategorizálva |
| Modell: | CLWI-KPLEX-BATT |
Szüksége van segítségre?
Ha segítségre van szüksége Crestron CLWI-KPLEX-BATT, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva Crestron
2 Április 2025
2 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
1 Április 2025
Útmutatók nincs kategorizálva
- nincs kategorizálva Domyos
- nincs kategorizálva Schaffner
- nincs kategorizálva Prompter People
- nincs kategorizálva Solo
- nincs kategorizálva Auto XS
- nincs kategorizálva Cyrus
- nincs kategorizálva Contax
- nincs kategorizálva A.O. Smith
- nincs kategorizálva Medeli
- nincs kategorizálva Unold
- nincs kategorizálva Chef's Choice
- nincs kategorizálva Ibiza Sound
- nincs kategorizálva Columbus
- nincs kategorizálva Nanni
- nincs kategorizálva Sunding
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025