Használati útmutató DeWalt D25940K

DeWalt nincs kategorizálva D25940K

Olvassa el alább 📖 a magyar nyelvű használati útmutatót DeWalt D25940K (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 4 felhasználó értékelte átlagosan 3.8 csillagra

Letöltés PDF

Oldal 1/4

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

D25940

Demolition Hammer

Marteaux de démolition

Martillo demoledor

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVOADVERTENCIA:

ANTES DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules

WARNING! Read and understand all instructions. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

•Keep bystanders, children, and visitors away while operating a power tool. Distractions

can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adapter plugs. Check with a qualified elec-

trician if you are in doubt as to whether the outlet is properly grounded. If the tools should

electrically malfunction or break down, grounding provides a low resistance path to carry

electricity away from the user. Applicable only to Class I (Grounded) tools.

•Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polar-

ized outlet. Do not change the plug in any way. Double Insulation eliminates the need for

the three wire grounded power cord and grounded power supply system. Applicable only

to Class ll tools.

•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

•Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock. Other liquids, such as perspiration, present the same haz-

ard.

•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

•When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-

ber, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

12 - 16 14 12 Not Recommended

PERSONAL SAFETY

•Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica-

tion. A moment of inattention while operating power tools may result in serious personal

injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts. Air vents may cover moving parts and should be avoided as

well.

•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and balance

enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing the tool. Such preventive safety measures reduce the risk of start-

ing the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are dan-

gerous in the hands of untrained users.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

•Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced before

using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow mainte-

nance instructions may create a risk of electric shock or injury.

Additional Safety Instructions for Demolition Hammers

•Hold tool by insulated gripping surfaces (side handle and rear handles) when per-

forming an operation where the cutting tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the oper-

ator.

•Wear safety goggles or other eye protection. Hammering operations cause chips to fly.

Flying particles can cause permanent eye damage. Wear a dust mask or respirator for appli-

cations that generate dust.

•Keep a firm grip on the tool at all times. Do not attempt to operate this tool without hold-

ing it with both hands. It is recommended that the side handle be used at all times. Operating

this tool with one hand will result in loss of control. Breaking through or encountering hard

materials such as re-bar may be hazardous as well.

•Do not operate this tool for long periods of time. Vibration caused by hammer action may

be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure

by taking frequent rest periods.

•Do not recondition bits yourself. Chisel reconditioning should be done by an authorized

specialist. Improperly reconditioned chisels could cause injury.

•Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and

bits may get extremely hot during operation. Small bits of broken material may damage bare

hands.

•Never lay the tool down until the bit has come to a complete stop. Moving bits could

cause injury.

•Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or mate-

rial chips could dislodge and cause injury.

•Slightly worn chisels can be resharpened by grinding.

NOTE: Do not overheat the bit (discoloration) while grinding a new edge. Badly worn chisels

require reforging. Do not reharden and temper chisels.

CAUTION: Wear appropriate personal hearing protection during use. Under some con-

ditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with approved

safety equipment, such as those dust masks that are specially designed to filter out microscop-

ic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may pro-

mote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

• The label on your tool may include the following symbols.

V................volts A......................amperes

Hz..............hertz W ....................watts

min ............minutes ....................alternating current

..........direct current no ....................no load speed

................

Class II Construction

......................

earthing terminal

..............safety alert symbol .../min revolutions per minute................

OPERATION

Your tool is powered by a D WALT built motor. Be sure your power supply agrees with name-E

plate marking.

Voltage decreases of more than 10% will cause loss of power and overheating. All DEWALT

tools are factory tested: if this tool does not operate, check the power supply.

Switch (Fig. 1)

The switch on your hammer is designed to lock-on.

To turn the tool on, press the rear half of the rocker switch (A) upward. To stop the tool, press

the forward half of the rocker switch.

Side Handle (Fig. 2)

Side handle may be rotated and angled for most comfortable use.

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more D WALT power tools: the yellow and black colorE

scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box con-

figuration; and the array of lozenge-shaped humps on the surface of the tool.

Questions? See us in the World Wide Web at www.dewalt.com

Termékspecifikációk

Márka:	DeWalt
Kategória:	nincs kategorizálva
Modell:	D25940K

Szüksége van segítségre?

Ha segítségre van szüksége DeWalt D25940K, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva DeWalt

DeWalt DWV012 Útmutató

4 Január 2025

DeWalt DCF403 Útmutató

3 Január 2025

DeWalt DCF503E Útmutató

3 Január 2025

DeWalt DCBPSC0550 Útmutató

3 Január 2025

DeWalt DCPS660 Útmutató

3 Január 2025

DeWalt DCE180 Útmutató

3 Január 2025

DeWalt DCB187 Útmutató

12 December 2024

DeWalt DCB184G Útmutató

12 December 2024

DeWalt DCB183G Útmutató

12 December 2024

DeWalt DCB185 Útmutató

12 December 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA SR-P Útmutató

10 Április 2025

Soundstream VRN-64HBL Útmutató

10 Április 2025

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025

Planet PWR-240-48 Útmutató

9 Április 2025

CaterChef 445001 Útmutató

9 Április 2025

IFM E40581 Útmutató

9 Április 2025

Livn Bolt Útmutató

9 Április 2025

Livn Beats Útmutató

9 Április 2025

Alpine DP2-40C-BC Útmutató

9 Április 2025

IFM O3R252 Útmutató

9 Április 2025