Használati útmutató Dürkopp Adler 1180

Dürkopp Adler varrógép 1180

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Dürkopp Adler 1180 (33 oldal) a varrógép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 3.5 felhasználó értékelte átlagosan 4.3 csillagra

Letöltés PDF

Oldal 1/33

Instructions for service

1180 - 5

Minerva Boskovice, a.s., Sokolská 60, CZ - 680 17 Boskovice

Tel.: +420-501-453434, 453433, 494111 Fax: +420-501-452165 http://www.minerva-boskovice.com

Edition: 06/2001 Printed in Czech Republic 735 342 000 467

CONTENTS:

1. General safety instructions ............................................................................................................................................... 1

2. Introduction .......................................................................................................................................................................... 1

3. Head of the sewing machine .............................................................................................................................................. 2

3. 1 Hook and hook box .................................................................................................................................................................. 2

3.1.1 Description

3.1.2 Height setting of the hook

3.1.3 Setting the distance of the hook from the needle

3.1.4 Angular setting of the hook (timing)

3.1.5 Protection of the needle and of the hook point

3.1.6 Setting of the bobbin case opener

3.1.7 Setting the regulation of the hook lubrication

3.1.8 Replacement of the hook

3.1.9 Setting the gear

3.1.10 Dismantling of the hook box

3.2 Needle and thread mechanism ................................................................................................................................. 5

3.2.1 Description

3.2.2 To check the handwheel angular adjustment

3.2.3 Height setting of the needle bar

3.2.4 Angular setting of the pin of the thread mechanism

3.2.5 Side setting of the needle bar holder

3.2.6 Setting the needle (the needle bar holder) in the direction of sewing (fine setting)

3.3 Throat plate ............................................................................................................................................................................... 7

3.3.1 Description

3.3.2 Mounting and removing the throat plate and its insert

3.3.3 Setting the throat plate and its insert

3.4 Thread tensioners and limiter ................................................................................................................................. 8

3.4.1 Description

3.4.2 Setting the tension of main and auxiliary tensioners

3.4.3 Setting the tensioning mechanism of the main tensioner

3.4.4 Setting the adapting spring

3.4.5 Setting the thread limiter

3.5 Feeding mechanism of the needle feed and of the lower feed wheel .................................................................... 10

3.5.1 Description

3.5.2 Stitch length mechanism

3.5.2.1 Setting the upper eccentric

3.5.2.2 Setting the prop

3.5.2.3 a Forward and rearward stitch length distribution (rough)

3.5.2.3 b Forward and rearward stitch length distribution (fine)

3.5.2.4 Setting of the control knob (including the stitch length limitation)

3.5.3 Setting the needle feed (rough)

3.5.4 Lower feed wheel

3.5.4.1 Feeding clutches

3.5.4.1.1 Description

3.5.4.1.2 Setting the lever of the second step of feeding(angle, position)

3.5.4.1.3 Setting of the lower eccentric

3.5.4.1.4 Setting the engagement and disengagement of the clutches

3.5.4.2 Wheel feeder and its post

3.5.4.2.1 Height setting of the feeder

3.5.4.2.2 Replacement of the feeder

3.5.5 Setting the top roller (pressing force, height)

3.6 Feeding mechanism of the top roller ....................................................................................................................15

3.6.1 Description

3.6.2 Side setting of the indented lower pulley

3.6.3 Side setting of the indented upper pulley

3.6.4 Setting the tensioning roller

3.6.5 Replacement of the indented belt

3.6.6 Setting the feeding difference

3.6.7 Replacement of the friction wheels of the drive conversion unit

3.6.8 Top roller

3.6.8.1 Selection of the top roller diameter

3.6.8.2 Forward, rearward and side setting

3.6.8.3 Setting the gear clearance

3.6.8.4 Replacement of the top roller

3.7 Setting the presser foot lift .................................................................................................................................... 19

3.8 Bobbin winder ....................................................................................................................................................... 20

3.8.1 Description

3.8.2 Setting the bobbin winder stop

3.8.3 Setting the friction gear

3.9 Safety clutch .......................................................................................................................................................... 21

3.9.1 Description

3.9.2 Setting the disengaging moment

3.10 Indented belt transmission ................................................................................................................................... 21

3.10.1 Setting the tensioning roller of the indented belt

3.10.2 Replacing the indented belt

3.11 V-belt, motor - head .............................................................................................................................................. 22

3.11.1 Tensioning

3.11.2 Replacing the V-Belt

3.12 Lubrication ............................................................................................................................................................. 23

3.12.1 Description

3.12.2 Refilling oil

3.12.3 Multiple oil use

4. Thread trimming ............................................................................................................................................................... 24

4.1 Description of the trimming mechanism

4.2 Setting the pickup roller

4.3 Setting the cam

4.4 Setting the fork

4.5 Setting the moving knife

4.6 Setting the fixed knife

4.7 Setting the retaining spring of the hook thread

4.8 Setting switching of the electromagnets

5. Lifting the top roller by electromagnet ........................................................................................................................... 26

5.1 Description

5.2 Setting the electromagnet pin

5.3 Setting the electromagnet current

5.4 Assembly of the top roller lifting electromagnet

6. Backtacking using electromagnet .................................................................................................................................... 27

6.1 Description

6.2 Electromagnet height setting

6.3 Setting the position of push-buttons

6.4 Change of the function of push-buttons

7. Connecting the electric elements on the machine head ................................................................................................ 28

8. Drive, control panel, position sensor ........................................................................................................................... 28

9. Lighting ........................................................................................................................................................................... 28

9.1 Mounting on the machine head

9.2 Lamp replacement

10. Maintenance (table of operations) ................................................................................................................................. 29

11. Setting the machine according to the sewing category .................................................................................................. 29

11.1 Introduction

11.2 Table of setting the machine according to the sewing category