Használati útmutató Elektrobock CV701
Elektrobock
párásító
CV701
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Elektrobock CV701 (4 oldal) a párásító kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 4.5 felhasználó értékelte átlagosan 4.9 csillagra
Oldal 1/4

SENSOR
HUMIDITY
When the set relative humidity (RH) is reached, the
connected device (fan, hood, signaling equipment, etc.).
C
C
C
CV701
V701
V701
V701
CV701
Pb
LEAD FREE
in acco rdanc e
with RoHS
MADE IN CZECH REPUBLIC
MAX.
15-200 W
RH
20-95 %

CV701 is an ideal solution for places where there is a high risk of mold (on
masonry, windows, tiles).
The main function of the CV701 is to control the fan (ventilation) with respect to
the size of the relative humidity (RH) in the room (RH is the percentage of water
vapor content in air at a given temperature compared to air vapor fully saturated at
the same temperature). High RH can cause condensation of water vapor and thus
the formation of mold. Molds not only damage property, but can also seriously
endanger human health (allergies, asthma).
DESCRIPTION
CONSTRUCTION
Remove the terminal cover (Fig.1). Connect the 230V / 50Hz power
supply to the and terminals (the rst two from the right). Connect N L
the device we want to switch to the terminals marked and N, eg the OUT
fan (diagram no. 1). The terminal marked number 1 does not have to be
connected, it is used for connection of external control (diagram no. 2).
After connecting the wires, return the terminal box cover and attach the
CV701 to the installation box.
We always change the fuse for the same type F2A / 1500A, 250V.
Only a person may install and replace the fuse (without voltage)
with the appropriate qualications.
NOTICE
The humidity sensor must be installed at least 1 m from the fan! Select
a location where the sensor will not be aected by direct warm airow
from the heater, sunlight, or other disturbances.
scheme no.1 scheme no.2
230 V/50 Hz 230 V/50 HzL

SETTINGS
At the required humidity (ie whenever we want it to occur
to switch on the connected device) turn the control element (Fig.2)
counterclockwise until the red LED lights up and the connected device
is switched on.
When the set RH value is exceeded, CV701 starts automatically regulate
room ventilation. If the humidity does not reach the set value, the CV701
is inoperative.
When connected with an external switch (diagram no. 2), it is possible to
manually regulate the ventilation regardless of the humidity in the room.
Fig.1 Fig.2
screw
(to remove the cover)
control element
(RH setting)
terminal blocks
(for connecting wires)
red LED
(indication of switching)
position 1
corresponds to
20% RH
(indicative value)
position 10
corresponds to 95%
RH
(indicative value)
Termékspecifikációk
Márka: | Elektrobock |
Kategória: | párásító |
Modell: | CV701 |
Szüksége van segítségre?
Ha segítségre van szüksége Elektrobock CV701, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók párásító Elektrobock
7 Augusztus 2024
Útmutatók párásító
- párásító ProfiCare
- párásító Cecotec
- párásító Tefal
- párásító Ravanson
- párásító Boneco
- párásító Maxwell
- párásító Jata
- párásító Alecto
- párásító Olimpia Splendid
- párásító DeLonghi
- párásító Winland
- párásító Sharp
- párásító Ruggard
- párásító Minuteman
- párásító Danby
Legújabb útmutatók párásító
19 Március 2025
4 Január 2025
31 December 2025
29 December 2024
29 December 2024
29 December 2024
29 December 2024
28 December 2024
28 December 2024
27 December 2024