Használati útmutató Emko Eco PID

Emko hőmérséklet szabályozó Eco PID

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Emko Eco PID (4 oldal) a hőmérséklet szabályozó kategóriában. Ezt az útmutatót 23 ember találta hasznosnak és 12 felhasználó értékelte átlagosan 5.0 csillagra

Letöltés PDF

Oldal 1/4

PO1

AL2

°C

°F

Eco

PO2

AL1

PO1

AL2

°C

°F

Eco

PO2

AL1

Eco PID, PID Temperature Control Un�t

- 3 d�g�t process (PV) and 4 d�g�t set (SV) d�splay

- Temperature sensor �nput (TC,RTD)

- Programmable ON/OFF, P, PI, PD and PID control forms

- Adaptat�on of PID Coeff�c�ents to the system w�th Self-Tune and Auto-Tune

- Programmable Heat�ng or Cool�ng Funct�ons for Control Output

- Selectable Alarm Funct�ons for Alarm Output

- Ser�al RS485 Commun�cat�on (opt�onal)

Introduct�on Brochure. ENG EcoPID 01 V04 10/19

Easy Access D�agram For Program Parameters

Panel Mount�ng

Enter Password w�th �ncrement

or decrement buttons.

Approve password

w�th Enter button

Ma�n Screen Password Screen

Eco ser�es temperature controllers are des�gned for measur�ng and controll�ng a

temperature value. They can be used �n many appl�cat�ons w�th the�r TC and RTD

temperature measurement �nput, mult�-funct�on control outputs, selectable alarm

funct�ons.

They are ma�nly used �n glass, plast�c, petro-chem�stry, text�le, automot�ve and mach�ne

product�on �ndustr�es. Accurate and advanced controll�ng �s performed w�th selectable

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct�ons.

SPECIFICATIONS

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)

Thermores�stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)

Measurement Range: Please refer to process �nput type select�on �n process menu

parameters sect�on.

Accuracy:

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh�ch one �s greater) ±1 d�g�t max.

Thermores�stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh�ch one �s greater) ±1 d�g�t

max.

Cold Junct�on Compensat�on: Automat�cally ±0.1°C/1°C

L�ne Compensat�on: Max�mum 10 Ohm

Sensor Break Protect�on: Upscale

Sampl�ng Cycle: 0.1 second

Input F�lter: Programmable

Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)

OUTPUT

Process Output: Relay (5A@250VV at res�st�ve load) or SSR Dr�ver Output

(Max�mum 10mA, Max. 12VZ )

Alarm Output: Relay (5A@250VV at res�st�ve load)

SUPPLY VOLTAGE (It must be determ�ned �n order)

230VV (±15%) 50/60Hz - 2VA

115VV (±15%) 50/60Hz - 2VA

100-240VV 50/60Hz - 2VA

24VV(±%15) 50/60Hz - 2VA

24VW (±%15) 50/60Hz - 2VA

10...30VZ - 2W

DISPLAY

Process D�splay: 16 mm Red 3 d�g�t LED D�splay

Set Value D�splay: 9 mm Orange 4 d�g�t LED D�splay

Led Ind�cators: PO1 (SSR Process Output Status Led), PO2 (Relay

Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),

ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operat�ng Temperature: 0...50ºC

Hum�d�ty : 0-90%RH (none condens�ng)

Protect�on Class: IP65 at front, IP20 at rear

We�ght: 150 gr.

D�mens�on: 48 x 48 mm, Depth: 86,5 mm

Panel CutOut: 46 x 46 mm

*1 - ON/OFF Hysteres�s parameter �s not act�ve unless parameter �s set as .

*2 - Soft Start parameters( , , ) �s not act�ve unless parameter �s set as .

*3 - Soft Start Control Output and Soft Start Control T�me parameters �s not act�ve �f parameter

�s set as .

*4 - PID control parameters are not act�ve unless parameter �s set as .

*5 - Alarm-2 parameters are not act�ve �f parameter �s set as .

*6 - Commun�cat�on parameters are not act�ve on dev�ces have no commun�cat�on module.

*7 - If �s d�fferent from 0 and user enters to program menu w�thout enter�ng the password

rot menu �s not shown.

Note: User can ex�t from any parameter screen w�thout sav�ng the values by press�ng button. If

no operat�on for 120 seconds, dev�ce automat�cally return to ma�n screen.

Easy Access D�agram For Sensor Break Output

Value From Ma�n Screen

Change the sensor break

output value w�th �ncrement

or decrement buttons.

Press Enter button to save

new sensor break output value

and ex�t.

PO2

PO1

AL1

AL2

°C

°F

Ma�n Screen

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

/ PO2

PO1

AL1

AL2

°C

°F

Ma�n Screen

Note1: User can ex�t from parameter screen w�thout sav�ng the

values by press�ng button. If no operat�on for 120 seconds, dev�ce

automat�cally ex�ts from parameter screen.

Note2: Sensor break output value can be adjusted on programm�ng

sect�on too.

Tune Operat�on

Start�ng the Tune operat�on

1- Enter to the parameter �n menu and select

or ,then press button for sav�ng parameter and turn to ma�n

screen. Or eas�ly press button for 3 seconds* �n ma�n screen.

2- Observe that bl�nks �n set d�splay.

*Only Auto tune can be started by th�s way.

Cancel�ng Tune operat�on:

1- If sensor breaks;

2- If tune operat�on can not be completed �n 8 hours;

3- Wh�le heat�ng self tune �s runn�ng, �f process value becomes

greater than process set value;

4- Wh�le cool�ng self tune �s runn�ng, �f process value becomes less

than process set value;

5- Wh�le tune operat�on �s runn�ng, �f user changes the process set

value;

6- Wh�le tune operat�on �s runn�ng, �f user changes the

parameter �n menu;

Then tune operat�on �s canceled, dev�ce cont�nues to run w�th former

PID parameters w�thout chang�ng PID parameters.

PID TEMPERATURE CONTROL UNIT

PID

Eco

D�mens�ons

PO2

PO1

AL1

AL2

°C

°F

PID

Eco

48 mm / 1.89 �nch

6 mm / 0.24 �nch

80,52 mm / 3.17 �nch

Max�mum 9 mm / 0.35 �nch

1- Before mount�ng the dev�ce �n your panel,

make sure that the cutout �s of the r�ght s�ze.

2- Check front panel gasket pos�t�on.

3- Insert the dev�ce through the cutout. If the

mount�ng clamps are on the un�t, put out them

before �nsert�ng the un�t to the panel.

4- Insert the mount�ng clamps to the two of

des�gnated holes that located four s�des of

dev�ce.

5- Drag the mount�ng clamps �n d�rect�on 5

unt�l the dev�ce completely �mmob�le w�th�n the

panel.

6- In order to remove dev�ce push on the

mount�ng clamp as shown w�th arrow 6 and

pull back.

Access and Change Set Values

Press �ncrement or decrement

button to change process set value.

Press Enter button to save new

set value and return the ma�n screen.

Ma�n Screen

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

Ma�n Screen

PO2

PO1

AL1

AL2

°C

°F

/ PO2

PO1

AL1

AL2

°C

°F

Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000

Note-1: User can ex�t from set value sect�on w�thout sav�ng the values by press�ng button. If no

operat�on for 120 seconds, dev�ce automat�cally ex�ts from Set Value sect�on.

Note-2: Set value can be adjusted between Set Value Low and H�gh L�m�t ( - ).

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

/PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

*2,3

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

Press Program button

to access password screen.

Electr�cal W�r�ngs

The Dev�ce w�th One Relay:

The Dev�ce w�th Two Relays:

To reduce the effect of electr�cal no�se on dev�ce, low voltage l�ne (espec�ally sensor

�nput cable) w�r�ng must be separetely from h�gh current and voltage l�ne. If poss�ble,

use sh�elded cable and sh�eld must be connected to ground only one s�de.

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

Process

Input

5A@250V

Ser�al Commun�cat�on

(RS485, Modbus RTU)

A+

B-

PID

Eco

PT-100

Supply

Sw�tch

Supply

Voltage

1A T

Fuse

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

Ser�al Commun�cat�on

(RS485, Modbus RTU)

A+

B-

PID

Eco

PT-100

Supply

Sw�tch

Supply

Voltage

1A T

Fuse

Warranty

EMKO Elektron�k warrants that the equ�pment del�vered �s free from

defects �n mater�al and workmansh�p. Th�s warranty �s prov�ded for a

per�od of two years. The warranty per�od starts from the del�very

date.

Th�s warranty �s �n force �f duty and respons�b�l�t�es wh�ch are

determ�ned �n warranty document and �nstruct�on manual performs

by the customer completely.

Ma�ntenance

Repa�rs should only be performed by tra�ned and spec�al�zed

personnel. Cut power to the dev�ce before access�ng �nternal parts.

Do not clean the case w�th hydrocarbon-based solvents (Petrol,

Tr�chlorethylene etc.). Use of these solvents can reduce the

mechan�cal rel�ab�l�ty of the dev�ce. Use a cloth dampened �n ethyl

alcohol or water to clean the external plast�c case.

Other Informat�ons

Manufacturer Informat�on:

Emko Elektron�k Sanay� ve T�caret A.Ş.

Dem�rtaş Organ�ze Sanay� Bölges� Karanf�l Sk. No:6 16369

BURSA/TURKEY

Phone: +90 224 261 1900

Fax: +90 224 261 1912

Repa�r and Ma�ntenance Serv�ce Informat�on:

Emko Elektron�k Sanay� ve T�caret A.Ş.

Dem�rtaş Organ�ze Sanay� Bölges� Karanf�l Sk. No:6 16369

BURSA/TURKEY

Phone: +90 224 261 1900

Fax : +90 224 261 1912

Before comm�ss�on�ng the dev�ce, parameters must be set �n

accordance w�th des�red use. Incomplete or �ncorrect conf�gurat�on

can cause dangerous st�uat�ons.

Because of l�m�ted mechan�cal l�fe of relay output contact, SSR

output �s recommended wh�ch the dev�ce use PID control algor�tm.

The dev�ce w�th ON/OFF control algor�tm, hysteres�s parameter must

be set a su�table value for your system, to avo�d too much relay

sw�tch�ng.

Vac,

Vdc,

Vdc or Vac can be appl�ed

: Commun�cat�on Parameters (Only for dev�ces w�th RS-485 com.)

: Protec�on Menu Parameters

: Commun�cat�on access�ng address of dev�ce. (Default: 1) Modbus

Address: 40056

: Commun�cat�on Baud Rate. (Default: 3) Modbus Address: 40057

: 1200 Baud Rate.

: 2400 Baud Rate.

: 4800 Baud Rate.

: 9600 Baud Rate.

: 19200 Baud Rate.

: 38400 Baud Rate.

: Par�ty Select�on for Commun�cat�on. (Default: 0) Modbus Address: 40058

: No Par�ty.

: Odd Par�ty.

: Even Par�ty.

: Stop B�t Select�on for Commun�cat�on. (Default: 0) Modbus Address: 40059

: 1 Stop B�t.

: 2 Stop B�t.

: Password for access�ng to the programm�ng sect�on. It can be adjusted from 0 to

9999. If �s 0, password screen �s not seen. If �s d�fferent from 0 and user

enters to the menu pages w�thout enter�ng the password, all the menus can be

observed except protect�on menu . But dev�ce does not allow to do any changes

�n parameters. (Default: 0) Modbus Address: 40063

: User default parameters. Th�s parameter �s used for sav�ng all parameters to

restore later or restore all parameters saved before. If �s chosen, all parameters

saved before are restored. If �s chosen, all parameters saved to restore later. If

�s chosen, noth�ng �s changed. (Default: ) Modbus Address: 40064

: Th�s parameter �s used for restore factory defaults. If �s chosen, factory

defaults parameters restored. If �s chosen, noth�ng �s changed. (Default: )

Modbus Address: 40065

Remove all �nput/output connect�ons on term�nals before restor�ng

parameters to user/factory defaults.

Modbus Addresses of Dev�ce Operat�on Info. (Read Input Reg�ster)

Modbus Address: 30000

Modbus Address: 30001

Modbus Address: 30002

D�splayed Temperature Value

Status of LEDs: b�t.1 ALR1, b�t.2 ALR2, b�t.9 °C

b�t.10 °F, b�t.11 PO2, b�t.12 PO1

Status of Dev�ce: b�t.0 Sensor Break Status

Alarm Types

Alarm

Set

Alarm

Hysteres�s

Alarm

Hysteres�s

Alarm

Set

Process

Set

Process

Set

Alarm

Set

Alarm

Hysteres�s

Alarm

Hysteres�s

Process

Set

Process

Set

Alarm

Set

Alarm

Output

Alarm

Output

Alarm

Output

Alarm

Output

Process Value

Process H�gh

Alarm

Process Low

Alarm

Dev�at�on H�gh

Alarm

Dev�at�on Low

Alarm

: Alarm-1 set value. (Default: 300) Modbus Address: 40036

: Alarm-1 hysteres�s value. It can be adjusted from %0 to %50 of the scale

( - ). (Default: 0) Modbus Address: 40037

: Alarm-1 type select�on. (Default: ) Modbus Address: 40038

: Alarm-1 set low l�m�t parameter. It can be adjusted from operat�on scale m�n�mum

to alarm-1 set h�gh l�m�t. (Default: 0) Modbus Address: 40039

: Alarm-1 set h�gh l�m�t parameter. It can be adjusted from alarm-1 set low l�m�t to

operat�on scale m�n�mum. (Default: 500) Modbus Address: 40040

: Alarm-1 on Delay T�me. It can be adjusted from 0 to 9999 seconds. (Default: 0)

Modbus Address: 40041

: Alarm-1 off Delay T�me. It can be adjusted from 0 to 9998 seconds. If �t �s h�gher

than 9998, �s seen on the screen and alarm latch�ng output �s selected. In alarm

latch�ng output mode �n order to make pass�ve alarm outputs, press enter button at

ma�n screen. (Default: 0) Modbus Address: 40042

: Alarm-1 Menu Parameters

PID menu parameters can be seen only �f parameter �s .

: If tune parameter �s set to or , dev�ce start to calculate PID

parameters automat�cally. (Default: ) Modbus Address: 40027

: Proport�onal band. It can be adjusted from %1.0 to %100.0. (Default: 10.0)

Modbus Address: 40028

: Integral T�me. It can be adjusted from 0 to 3600 second. (Default: 100) Modbus

Address: 40029

: Der�vat�ve T�me. It can be adjusted from 0.0 to 999.9 second. (Default: 25.0)

Modbus Address: 40030

: Output Control Per�od. It can be adjusted from 0.5 to 150 second. (Default: 1.0)

Modbus Address: 40031

: Set value offset. (Set + ) �s used as set value �n PID calculat�ons. Th�s

parameter �s used for sh�ft�ng the proport�onal band. It can be adjusted from (- /2) to

( /2). (Default: 0) Modbus Address: 40032

: PID Menu Parameters

: Alarm-2 Menu Parameters (Only for dev�ces w�th two relays)

Alarm-2 menu parameters can be seen only �f parameter �s .

: Alarm-2 set value. (Default: 400) Modbus Address: 40046

: Alarm-2 hysteres�s value. It can be adjusted from %0 to %50 of the Scale

( - ). (Default: 0) Modbus Address: 40047

: Alarm-2 type select�on. (Default: ) Modbus Address: 40048

: Alarm-2 set low l�m�t parameter. It can be adjusted from operat�on scale m�n�mum

to alarm-2 set h�gh l�m�t. (Default: 0) Modbus Address: 40049

: Alarm-2 set h�gh l�m�t parameter. It can be adjusted from alarm-2 set low l�m�t to

operat�on scale max�mum. (Default: 500) Modbus Address: 40050

: Alarm-2 on delay t�me. It can be adjusted from 0 to 9999 seconds. (Default: 0)

Modbus Address: 40051

: Alarm-2 off delay t�me. It can be adjusted from 0 to 9998 seconds. If �t �s h�gher

than 9998, �s seen on the screen and Alarm Latch�ng Output �s selected. In

alarm latch�ng output mode �n order to make pass�ve alarm outputs, press enter

button at ma�n screen. (Default: 0) Modbus Address: 40052

Installat�on

In package,

-One p�ece un�t

-Two p�eces mount�ng clamp

-One p�ece �nstruct�on manual

A v�sual �nspect�on of th�s product for poss�ble damage occured

dur�ng sh�pment �s recommended before �nstallat�on. It �s your

respons�b�l�ty to ensure that qual�f�ed mechan�cal and electr�cal

techn�c�ans �nstall th�s product.

If there �s danger of ser�ous acc�dent result�ng from a fa�lure or defect

�n th�s un�t, power off the system and the electr�cal connect�on of the

dev�ce from the system.

The un�t �s normally suppl�ed w�thout a power sw�tch or a fuse. Use

power sw�tch and fuse as requ�red.

Be sure to use the rated power supply voltage to protect the un�t

aga�nst damage and to prevent fa�lure.

Keep the power off unt�l all of the w�r�ng �s completed so that electr�c

shock and trouble w�th the un�t can be prevented.

Never attempt to d�sassemble, mod�fy or repa�r th�s un�t. Tamper�ng

w�th the un�t may results �n malfunct�on, electr�c shock or f�re.

Do not use the un�t �n combust�ble or explos�ve gaseous

atmospheres. Dur�ng the equ�pment �s putted �n hole on the metal

panel wh�le mechan�cal �nstallat�on some metal burrs can cause

�njury on hands, you must be careful.

Montage of the product on a system must be done w�th �t’s mount�ng

clamp. Do not do the montage of the dev�ce w�th �nappropr�ate

mount�ng clamp. Be sure that dev�ce w�ll not fall wh�le do�ng the

montage.

It �s your respons�b�l�ty �f th�s equ�pment �s used �n a manner not

spec�f�ed �n th�s �nstruct�on manual.

Before beg�nn�ng �nstallat�on of th�s product, please

read the �nstruct�on manual and warn�ngs below

carefully.

Error Messages

Dev�at�on Range

H�gh Alarm

Process

Set

Alarm

Set

Process

Set

Alarm

Hysteres�s

Alarm

Output

Process Value

Process

Set

Alarm

Set

Process

Set

Process

Set

Alarm

Set

Alarm

Hysteres�s

Alarm

Hysteres�s

Alarm

Output

Process Value

Dev�at�on Range

Alarm

1-Sensor fa�lure �n analog �nputs. Sensor connect�on �s wrong or there

�s no sensor connect�on.

2-If programm�ng sect�on enter�ng password �s d�fferent from “0” and

user accesses to the parameter by enter button w�thout enter�ng the

password and wants to change a parameter, the warn�ng message �s

shown on the bottom d�splay as shown on the left. Dev�ce does not

allow to do any changes w�thout enter�ng the password correctly.

3-If value that �s read from the analog �nput �s lower than process set

low l�m�t parameter value ( ), value on the top d�splay starts to bl�nk

as shown on the p�cture.

4-If value that �s read from the analog �nput �s h�gher than process set

h�gh l�m�t parameter value ( ), value on the top d�splay starts to

bl�nk as shown on the p�cture.

5-If value that �s read from the analog �nput �s lower than sensor scale

low l�m�t, value on the top d�splay starts to bl�nk as shown on the

p�cture.

6-If value that �s read from the analog �nput �s h�gher than sensor scale

h�gh l�m�t, value on the top d�splay starts to bl�nk as shown on the

p�cture.

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

Process

Set

Alarm

Set

Process

Set

Process

Set

Alarm

Set

Alarm

Hysteres�s

Alarm

Hysteres�s

Alarm

Output

Process Value

Dev�at�on Band

Alarm

: Control Menu Parameters

: Th�s parameter determ�nes, wh�ch output w�ll be Process control output. If �s

chosen, process output �s relay output, �f �s chosen, process output �s SSR output.

(Default: ) Modbus Address: 40015

: Process Type Select�on. It can be (Heat�ng) or (Cool�ng).(Default: )

Modbus Address: 40016

: Process Control Type Select�on. It can be or . (Default: ) Modbus

Address: 40017

: Hysteres�s value. It can be adjusted from %0 to %50 of the Scale ( - ).

If = , then th�s parameter can be seen. (Default: 3) Modbus Address: 40018

: Sensor Break Output Value. It can be adjusted from %0 to %100. (Default: 0.0)

Modbus Address: 40019

: The cho�ce of d�splayed text on process value d�splay when sensor �s broken.

It can be or . (Default: ) Modbus Address: 40020

: Soft Start Set value. Dev�ce operates �n Soft Start mode, unt�l the temperature

reaches Soft Start set value. If �s selected, Soft Start mode �s d�sabled. (Default: )

Modbus Address: 40021

: Soft Start Control Output. Th�s parameter determ�nes soft start mode control

output percentage. It can be adjusted from %10 to %90. (Default: 10.0) Modbus

Address: 40022

: Soft Start Control T�me. Th�s parameter determ�nes soft start mode control t�me.

(Default: 1.0) Modbus Address: 40023

: Process Menu Parameters

: Process �nput type select�on; (Default: ) Modbus Address: 40004

: J type (Fe,Cu,N�) Thermocouple , -199ºC,900ºC ; -199ºF,999ºF

: J type (Fe,Cu,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF

: K type (N�,Cr,N�) Thermocouple , -199ºC,999ºC ; -199ºF,999ºF

: K type (N�,Cr,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF

: R type (Pt13%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF

: R type (Pt13%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF

: S type (Pt10%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF

: S type (Pt10%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF

: T type (Cu,Cu,N�) Thermocouple , -199ºC,400ºC ; -199ºF,752ºF

: T type (Cu,Cu,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF

: L type (N�,Cr,Co / N�,Fe,Mn,Cu) Thermocouple , -150ºC,800ºC ; -199ºF,999ºF

: L type (N�,Cr,Co / N�,Fe,Mn,Cu) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF

: Cu-50 , -199ºC,200ºC ; -199ºF,392ºF

: Cu-50 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF

: Pt-100 , -199ºC,650ºC ; -199ºF,999ºF

: Pt-100 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF

: Un�t Select�on. or can be chosen. (Default: ) Modbus Address: 40005

: Operat�on Scale m�n�mum (Low L�m�t) value. It changes accord�ng to the process

�nput type and scale. (Default: -199) Modbus Address: 40006

: Operat�on Scale max�mum (H�gh L�m�t) value. It changes accord�ng to the

process �nput type and scale. (Default: 900) Modbus Address: 40007

: Process Set value Low L�m�t. M�n�mum set value �s def�ned w�th th�s parameter.

It can be adjusted between Operat�on Scale m�n�mum and max�mum ( - )

values. (Default: -199) Modbus Address: 40008

: Process Set value H�gh L�m�t. Max�mum set value �s def�ned w�th th�s parameter.

It can be adjusted between Operat�on Scale m�n�mum and max�mum ( - )

values. (Default: 900) Modbus Address: 40009

: D�splay offset for process value. It can be adjusted from -10% of scale to 10% of

scale. It �s added to the process d�splay value. (Default: 0) Modbus Address: 40010

: Def�ne f�lter t�me(sec) for d�splayed value. (Default: 1.0) Modbus Address: 40011

Order�ng Informat�on

Eco PID ( 48x48 DIN 1/16 )

D�mens�on

48x48 DIN 1/16

4 .

S .

Outputs-1

1 x Relay Output (5A@250VV at Res�st�ve Load) (NO,C)

2 x Relay Output (5A@250VV at Res�st�ve Load) (NO,NO,C)

S SSR Dr�ver Output (Max. 10mA, Max. 12VZ)

Outputs-2

Commun�cat�on

None

485

RS-485 Commun�cat�on

10...30VZ

115VV (±%15) 50/60Hz

230VV (±%15) 50/60Hz

100-240VV 50/60Hz1

24VV (±%15) 50/60Hz

Customer

24VW (±%15) 50/60Hz2

Supply VoltageB

Termékspecifikációk

Márka:	Emko
Kategória:	hőmérséklet szabályozó
Modell:	Eco PID

Szüksége van segítségre?

Ha segítségre van szüksége Emko Eco PID, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hőmérséklet szabályozó Emko

Emko ESM-1520-N Útmutató

28 Augusztus 2024

Emko ECO PID+ Útmutató

28 Augusztus 2024

Emko Eco PID Útmutató

28 Augusztus 2024

Emko Eco Lite Útmutató

28 Augusztus 2024

Emko CHANNEL8A-N Útmutató

25 Augusztus 2024

Emko ESM-7720 Útmutató

25 Augusztus 2024

Emko ESM-3711-CN Útmutató

25 Augusztus 2024

Emko ESM-4410 Útmutató

25 Augusztus 2024

Emko ESM-4435 Útmutató

25 Augusztus 2024

Emko ESM-3720 Útmutató

17 Augusztus 2024

Útmutatók hőmérséklet szabályozó

Legújabb útmutatók hőmérséklet szabályozó

Techno Line WS 9245 Útmutató

28 December 2024

Techno Line WS 9003 Útmutató

28 December 2024

Techno Line WS 9114 Útmutató

28 December 2024

Techno Line WS 9117 Útmutató

28 December 2024

Techno Line WS 9900 Útmutató

28 December 2024

Techno Line MA 10260 Útmutató

28 December 2024

Techno Line WS 9172 Útmutató

28 December 2024

Berker 75642039 Útmutató

17 December 2024

Berker 75643039 Útmutató

17 December 2024

Hager WH27441207C Útmutató

13 December 2024