Használati útmutató Emos P5763

Emos Ajtócsengő P5763

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Emos P5763 (75 oldal) a Ajtócsengő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/75
3402060001_31-P5763_00_01_WEB 80 × 120 mm
www.emos.eu
P5763
GB Wireless Doorchime & Repeater
CZ Bezdrátový zvonek & prodlužovač signálu
SK Bezdrôtový zvonček & predlžovač signálu
PL Dzwonek bezprzewodowy & repeater sygnału
HU Vezeték nélküli csengő és jelismétlő
SI Brezžični zvonec in ojačevalnik signala
RS|HR|BA|ME Bežično kućno zvono i repetitor
DE Drahtlose Klingel und Signalverlängerung
UA Бездротовий дзвоник & подовжувач сигналу
RO|MD Sonerie fără r & prelungitor de semnal
LT Belaidis durų skambutis ir retransliatorius
LV Bezvadu durvju zvans un atkārtotājs
EE Juhtmevaba uksekell ja repiiter
BG Безжичен звънец и повторител
FR Carillon sans l & prolongateur de portée
IT Campanello senza li & ripetitore di segnale
ES Timbre inalámbrico & repetidor de señal
NL Draadloze deurbel & signaalverlenger
2
1
2
3 6
7
4
5
A B C
1
2
3
GB | Wireless Doorchime & Repeater
The set consists of a doorchime button (transmitter) and a chime (receiver). The chime is powered by
3× 1.5 V AA batteries.
The transmission between the button and the chime is done via radio waves at a frequency of 433.92 MHz. The
range depends on local conditions and reaches up to 120 m in open spaces without interference.
The set has a so-called “self-learning” function – the button is able to generate its own pairing code which is
then received by the chime and stored in its memory. The set can thus be expanded with additional buttons.
Their “self-learning” function also prevents them from aecting neighbouring doorchimes.
The range of the button can be extended using the “repeater” function (signal repeater).
For proper usage of the wireless doorchime, read the instruction manual thoroughly.
Technical Specications
Transmission range: up to 120 m in an open area (can drop down to one fth in a busy area)
3
Button: water resistant; enclosure IP44
Pairing of chime and buttons: “self-learning” function
Pairing capacity: max. 8 buttons per 1 chime
Number of ringtones: 16
Transmission frequency: 433.92 MHz, 5 mW e.r.p. max.
Chime power supply: 3× 1.5 V AA batteries
Button power supply: 1× 3 V battery (type CR2032, included)
Includes: double-sided adhesive tape, screws
Chime Description (see Fig. 1)
1 – chime LED
2 – speaker
3 – ringing mode button
4 – volume settings button
5 – repeater button (signal repeating)
6 – opening for hanging on a wall
7 – battery compartment
Button Description (see Fig. 2)
A – battery
B – button for changing ringtone/erasing memory of paired buttons
C – ring button/LED
Opening the Rear Compartment of the Button (see Fig. 3)
Pairing the Button with the Chime
1. Remove the rear cover of the button with a screwdriver through the hole on the side (see Fig. 3).
Insert a 3 V battery, type CR2032, into the button. When inserting the battery, make sure to observe correct
polarity (+ polarity up)!
2. Insert 3× 1.5 V AA batteries into the battery compartment of the doorbell (use alkaline batteries only).
You will hear a “ding dong” tone.
The chime automatically switches to “self-learning” mode which lasts for 60 second.
3. During these 60 seconds, press the button you want to pair with the chime. If the chime receives signal
from the button, a tone will sound, the button will pair with the chime and the self-learning mode will
automatically end.
4. For pairing multiple buttons, repeat steps 1 to 3.
Note: Before pairing each button, the chime must be put into self-learning mode – remove and reinsert
3× 1.5 V AA batteries.
You can pair a maximum of 8 buttons per chime this way.
Note: The chime has an internal memory where it stores the codes of the currently paired buttons for cases of
power failure. Once power supply to the chime is restored, the chime will automatically enter self-learning mode
for 60 seconds. However, if no signal is received within these 60 seconds (new pairing is not performed), the
chime will automatically load the codes of the previously paired buttons after self-learning mode ends. There
is thus no need to pair buttons again after a power failure.

Termékspecifikációk

Márka: Emos
Kategória: Ajtócsengő
Modell: P5763

Szüksége van segítségre?

Ha segítségre van szüksége Emos P5763, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Ajtócsengő Emos

Emos

Emos P5712 Útmutató

31 December 2025
Emos

Emos P5733S Útmutató

14 December 2024
Emos

Emos P5729 Útmutató

14 December 2024
Emos

Emos P5728T Útmutató

14 December 2024
Emos

Emos P5729B Útmutató

14 December 2024
Emos

Emos P5705 Útmutató

14 December 2024
Emos

Emos P5750.2T Útmutató

14 December 2024
Emos

Emos P5760T Útmutató

14 December 2024
Emos

Emos P5733G Útmutató

14 December 2024
Emos

Emos P5760 Útmutató

14 December 2024

Útmutatók Ajtócsengő

Legújabb útmutatók Ajtócsengő

NuTone

NuTone LA305WL Útmutató

30 Március 2025
NuTone

NuTone BK131LWH Útmutató

30 Március 2025
NuTone

NuTone LA130WH Útmutató

30 Március 2025
NuTone

NuTone BK144LCL Útmutató

30 Március 2025
Alecto

Alecto ADB-37 Útmutató

16 Január 2025
Elektrobock

Elektrobock BZ33-MP3 Útmutató

10 Január 2025
Lorex

Lorex B861AJEB-E Útmutató

8 Január 2025
Ring

Ring Battery Doorbell Útmutató

2 Január 2025
Friedland

Friedland Evo D3200 Útmutató

31 December 2025
Vimar

Vimar ELVOX K40965 Útmutató

30 December 2025