Használati útmutató Fender KXR 200

Fender billentyűzet KXR 200

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Fender KXR 200 (7 oldal) a billentyűzet kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/7
T H E S O U N T H A T C R E A T E S L E G E N D SD
P/N 048502
Two hundred
Owner,s Manual
KEYBOARD
EXTENDED
RANGE
Your new Fender®KXR 200 keyboard amplifier is the result
of Fender's®ongoing dialog with many of today's top musi-
cians. The KXR 200 uses state of the art technology to
deliver clear, resonant and most importantly...musical
sound.
The KXR 200 is actually much more than a keyboard amp.
With its heavy-duty Fender®Special Design speaker and
dual piezo-electric horn, it could actually be classified as a
self-contained, portable P.A. system. The KXR 200 is suit-
able for almost any musical instrument requiring full-range
reinforcement, for example, electronic keyboards,
acoustic/electric guitar, electric violin and also vocals.
Compact packaging and high output power make the KXR
200 the perfect full-range instrument amplifier for
rehearsal, studio or performances.
The preamp section of the KXR 200 features four indepen-
dent channels. Channels one, two, and three each feature
a single 1/4 inch, high-impedance-input jack, a three-
band equalizer, a channel volume control, an effects send
control and a reverb send control. Emphasizing on vocal,
channel four is equipped with a low impedance XLR jack in
addition to the 1/4 inch jack. Furthermore, channel four
also features a four-band equalizer centered around the
vocal frequencies, while still covering the whole audible
audio spectrum. Channel four is also equipped with a
channel volume control, an effects send control and a
reverb send control. In addition to the features mentioned
above, each channel also possesses an independent effects
loop insertion point on the rear panel. This feature makes
the KXR 200 even more versatile.
The KXR 200 is also equipped with a master section which
contains a master volume control, an effect return control, a
reverb return control, an effects send jack, an effects return
jack, and a line-out portion comprising of a 1/4 inch and
XLR jacks.
The KXR 200 keyboard amplifier was designed to give
years of reliable service under all conditions and is
equipped with a unique implementation of our exclusive,
defeatable DELTACOMPTM compressor system. When
DELTACOMPTM is engaged, it is practically impossible to
cause the power amplifier to clip (distort). With DELTA-
COMPTM, apparent compressor release time is kept short,
yet waveform distortion is kept to a minimum at low fre-
quencies.
The selection of a Fender®amplifier will reward you with
years of quality music in a wide range of sonic possibilities.
This manual is designed to familiarize you with the features
and functions of your KXR 200 amplifier. Read this manu-
al carefully so you will benefit from these features as soon
as you start using your new Fender®amplifier.
The built-in quality of a Fender®amplifier is the result of
over four decades of dedication in the combined skills of
the Fender®design team. That’s why we proudly say,
FENDER®... The Sound That Creates Legends.
INTRODUCTION
CHANNEL 1 INPUT (1/4 INCH) - Plug-in connector for
instruments. This balanced input can handle as much
as 8V R.M.S.
CHANNEL 1 VOLUME CONTROL - This control adjusts
the preamplifier gain of channel 1. It works in con-
junction with the Master Volume control ( item I) to set
the overall loudness of the amplifier for channel 1
only. Being a true “gain” control, it allows for the use
of a variety of microphones, keyboards or other instru-
ments with differing output signal levels. Low-level
instruments generally require a higher Channel
Volume setting while “hotter” keyboards will require a
lower setting.
CHANNEL 1 EQUALIZER - This equalizer allows
adjustments of the tonal characteristics of channel 1
before amplification. Each control provides a 12dB
boost or cut to bands of frequencies centered about
130, 540, and 4200 Hz. Note that all equalizer sec-
tions of the KXR 200 are designed so that if all center
frequencies are set at +12dB, a flat overall response
would be obtained. This is very useful if the signal
source is weak.
CHANNEL 1 EFFECTS SEND CONTROL - This control
works in conjunction with the effects send jack (item R),
effects return jack (item S), and the effect return con-
trol (item J) to , respectively, allow a desired amount of
preamp signal to be massaged, and to control the
amount of return signal that has gone through an
external effects device. The effects send control in con-
junction with the effects send jack could be used to
drive another KXR 200 as a slave amp. This is done
by connecting the effects send jack, with a standard
guitar cord, to the effects return jack of another KXR
200. Note that each channel could be set to send a
different amount of signal to the effects bus.
CHANNEL 1 REVERB SEND CONTROL - This control
works in conjunction with the reverb return control
(item K) to allow the amount of reverb to be mixed
with the dry signal. The amount of reverb-sent signal
is independent for each channel.
CHANNEL 2 AND 3 - These two channels are provid-
ed for two additional instruments. All the controls and
jacks operate in the same manner as those in channel
1. When not in use, it is best to turn the channel vol-
ume, the effects send and the reverb send controls all
the way down to avoid any amplification of unwanted
noise. Likewise, when not in use, the equalizer sec-
tions should be kept flat ( i.e. all knobs should be set at
12 O’clock).
CHANNEL 4 - This channel operates in the same man-
ner as the other three channels, but with the addition
of a few extra features: The XLR jack and an extra
band in the equalizer section. With the vocalist in
mind, the balanced, low impedance XLR jack provides
a suitable connection for a microphone. Furthermore,
the four-band equalizer was designed around the
A.
B.
C.
D.
E.
F,G.
H.
CHANNEL 3
VOLUME
5
0 10
HIGHMIDLOW
0
-12 +12
0
-12 +12
0
-12 +12
REVERBEFFECTS
5
0 10
5
0 10
SEND VOLUME
5
0 10
LOW
0
-12 +
1
CHANNEL 1
VOLUME
5
0 10
HIGHMIDLOW
0
-12 +12
0
-12 +12
0
-12 +12
REVERBEFFECTS
5
0 10
5
0 10
SEND
CHANNEL
VOLUME
5
0 10
MIDLOW
0
-12 + 12
0
-12 + 12
INPUT
INPUT
INPUT
INPUT MIC
AB C D EF
G
KXR 200 FRONT PANEL FUNCTIONS

Termékspecifikációk

Márka: Fender
Kategória: billentyűzet
Modell: KXR 200

Szüksége van segítségre?

Ha segítségre van szüksége Fender KXR 200, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók billentyűzet Fender

Fender

Fender KXR 100 Útmutató

12 Augusztus 2024
Fender

Fender KXR 60 Útmutató

9 Augusztus 2024
Fender

Fender KXR 200 Útmutató

3 Augusztus 2024

Útmutatók billentyűzet

Legújabb útmutatók billentyűzet

Tiptop Audio

Tiptop Audio Z-PASSIVE Útmutató

5 Április 2025
Tiptop Audio

Tiptop Audio MODEL 258T Útmutató

5 Április 2025
Tiptop Audio

Tiptop Audio Happy Ending Kit Útmutató

5 Április 2025
Tiptop Audio

Tiptop Audio SD808 Útmutató

5 Április 2025
Tiptop Audio

Tiptop Audio QART-QNTZ Útmutató

5 Április 2025
Gembird

Gembird KBS-P7-W-DE Útmutató

4 Április 2025
Trust

Trust Callaz GXT 834 Útmutató

30 Március 2025
Krom

Krom Kunai Útmutató

30 Március 2025
Savio

Savio Blackout X2 Útmutató

30 Március 2025
Evga

Evga Z10 Útmutató

30 Március 2025