Használati útmutató Festo NEBM-M23G15-EH-7.5-Q9N-S1LEG21

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Festo NEBM-M23G15-EH-7.5-Q9N-S1LEG21 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 9 felhasználó értékelte átlagosan 4.1 csillagra

6.

8.

NEBM-M23G15-...-S1LEG21

Motor cable

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Assembly instructions

8152341

2023-09

[8152343]

8152341

Translation of the original instructions

© 2023 all rights reserved to Festo SE & Co. KG

1

Applicable documents

All available documents for the product

è

www.festo.com/sp.

2Safety

2.1

Safety instructions

–Before working on the product: Switch off the power supply, ensure that it is off

and secure it against being switched on again.

2.2Intended use

The motor cable connects the servo motor EMMT-AS to the servo drive CMMP-AS.

2.3

Training of qualified personnel

Work on the product may only be carried out by qualified personnel who can

evaluate the work and detect dangers. The qualified personnel are trained in

electrical engineering.

3Additional information

–

Accessories

è

www.festo.com/catalogue.

4

Structure

4.1Product design

123

4

5

67

Fig.1

1

M23x1 socket

2

Sub-D plug

3

Wire end (6x)

4

Cable

5

Shielded connection

6

Line end

7

Screw (2x)

4.2Contact assignment

Electrical connection1

Field device side

SignalElectrical connection2

Controller side

1

Socket

3

Wire ends

1)

AUBU

BVBN

CWBK

DNot assigned–

PEPEGNYE

1BR-BUWH

2Not assigned–

3Not assigned–

4BR+GNWH

1)

Colour code in accordance with IEC 60757:2021-06

Tab. 1:Contact assignment for motor and brake

Electrical connection1

Field device side

SignalElectrical connection2

Controller side

1

Socket

2

Plug connector

5Up10

60V3

7DATA+12

8DATA-5

9CLK+13

10CLK-6

Tab. 2:

Encoder contact assignment

5

Assembly

5.1

Mounting electrical connection 1

1.

Align the socket to fit the plug.1

2.Connect the socket to the plug and click into position.1

5.2

Electrical connection 1 strain relief

NOTICE

Movements of the cable can cause malfunction and material damage.

Push-in connector on the field device is damaged by transferred application of

force.

•

Ensure sufficient strain relief at a maximum 30cm away from the socket.

5.3Mounting electrical connection2

1.

Fasten the shield connection to the servo drive with the shield clamp5

èOperating instructions, servo drive.

2.

Connect the wire ends in accordance with the contact assignment.3

3.

If necessary, lay the line end in a loop and secure with cable binders to6

maintain the required distance from other components.

4.

Align the plug to fit the socket.2

5.

Insert the plug into the socket.2

6.

Tighten the screws. Tightening torque: 0.4Nm±55%7

5.4Electrical connection 2 strain relief

•

Fix the cable in the area of the shield connection.5

Ä

Force is not transferred to the insulated wires.

5.5Wiring

Character-

istics

Cable characteristicsWiring

-ESuitability for energy chainsIn energy chain or flexible

Tab. 3:

Wiring

5.6Mounting in energy chain

1.

Lay out the energy chain lengthways.

2.

Place the cables in the energy chain without twisting them.

3.

Separate cables from each other using separators/drilled holes.

4.

Do not bind cables in bundles.

5.

Maintain spaceX. X10%of the cable diameterD.>

With the energy chain hanging vertically: increase the spaceX.

Align the energy chain in the working position:

–Make sure that the radius is greater than the bending radiusR of the

cables.

–

The cables can move freely in the bending radius KR of the energy chain.

Ä

The cable movement is not forced by the energy chain.

7.

Mount the energy chain corresponding instruction manual.è

Fasten the cables:

–

for short energy chains with a length 1m at both ends of the energy<

chain

–for long sliding energy chains with a length 1m at the driver end only>

Termékspecifikációk