Használati útmutató Garmin GPS 165

Garmin Navigator GPS 165

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Garmin GPS 165 (4 oldal) a Navigator kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
GPS 155/165
PILOT’S GUIDE
ADDENDUM
1. ROUTE RAIM PREDICTION FUNCTION
The GARMIN GPS 155/165 software versions 3.09 and higher incorporate a change to add the Route RAIM Prediction
Function ( ). This change evaluates the enroute RAIM availability over the entire route that the pilot intends toRAIM prd
fly. This enhancement meets the minimum system requirements required to conduct BRNAV/RNP-5 Operations (FAA
Advisory Circular 90-96).
1. From the Route Catalog Page (Figure 1), select the desired route for RAIM prediction (if the route is empty, enter
the route first). Highlight the route action field, select and press . The Route RAIM‘RAIM prd’ ENTER
Prediction Page will be displayed (Figure 2).
Figure 1. Route Catalog Page
Figure 2. Route RAIM Prediction Page
2. Highlight and enter depart time, depart date, enroute altitude, and enroute ground speed. Press ENTER to
accept.
NOTE
You may also enter the satellite ID number in the field for any satellite (1-32)‘rem sat’
which has been notamed as “out of service” during the flight, to exclude that particular
satellite from participating in predicting the Route RAIM availability. If nothing is entered
in the field, the unit assumes all satellites are usable.‘rem sat’
3. When all of the parameters are properly entered, the ‘Computefield will start flashing. Press . TheENTER
unit will start to predict the RAIM availability over the entire route, and the flashing field will‘Compute’
switch to ‘WAIT ->’, with the arrow sign continually rotating, indicating that the prediction is in progress.
1
NOTE
The prediction function takes a certain amount of time, depending on the route distance
and the enroute speed (i.e., 1000 nautical miles = approximately 2 minutes). The longer
the route distance, the longer the time. The slower the enroute speed, the longer the time.
Also, if there is a RAIM unavailability detected based on the associated requirement, the
prediction process will stop immediately, and display as shown in Figure 3. ‘NO RAIM
Figure 3. ‘NO RAIM’
4. If the entire route has RAIM availability, it will take a longer amount of time to complete, and display ‘RAIM
OK’ as shown in Figure 4.
NOTE
‘NO RAIMdoes not mean RAIM is unavailable for the entire route. It is actually the out-
come of detecting the RAIM unavailability for more than 5 minutes over the intended
flight, based on the BRNAV requirements.
Figure 4. ‘RAIM OK’
2. ROUTE SETTINGS PAGE (pg. 87, Pilot’s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which removes the Route Settings
Page which allowed Automatic Leg Selection and Automatic Leg Sequencing to be enabled/disabled by the pilot.
3. APPROACH SELECT PAGE (pg. 66, Pilots Guide)
GARMIN GPS 155/165 software (all versions):
An ‘unkn” (unknown) approach type is displayed on the Approach Select Page when the unit software does not know
how to display a new approach type in the database. DO NOT USE THIS APPROACH TYPE.
2
4. CANCELLING PARALLEL OFFSET NAVIGATION (pg. 56, Pilot’s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which cancels parallel offset naviga-
tion when entering the 30 NM arrival approach circle (if an approach is present in the active route to allow approach to
arm). The change also allows indication of approach not activeif parallel navigation is re-instated after approach nav-
igation has been armed.
5. I/O CHANNEL 2 SETUP PAGE
Figure 5. I/O Setup Page
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which adds the I/O Channel 2 Setup
Page to the user-defined settings that are available. The I/O setup page lets you configure the GPS 155/165 to output to
an RS-232 mapping device or a PC (with the optional GARMIN PC Kit or other mapping software) and select the appro-
priate baud rate. The I/O setup page only provides access to I/O channel 2 input/output. For information on using I/O
channel 1, please see your GPS 155/165 installation manual. The input option for channel 2 is intended for future inter-
facing capabilities and is not a selectable option at this time.
To change the output settings for I/O channel 2:
1. Press
S
and rotate
O
until the I/O setup page is displayed.
2. Use
K
to select ‘offor ‘plotting’ for output to an RS-232 device.
3. Rotate
O
to advance the cursor to the baud rate field.
4. Use
K
to select the desired baud rate (300, 1200, 2400, 4800, 9600).
5. Press CRSR to finish.
6. SID SELECTION (pg. 79, Pilot’s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which allows the pilot to select a SID
from the nearest airport when the active route does not have a departure airport as the first waypoint.
7. OFF-ROUTE DIRECT-TO WAYPOINT (pg. 59, Pilot’s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which retains a direct-to waypoint
as an off-route direct-to waypoint if a SID/STAR/Approach procedure waypoint is the active direct-to-waypoint when the
procedure is deleted and only the airport associated with the procedure remains in the active route.
3

Termékspecifikációk

Márka: Garmin
Kategória: Navigator
Modell: GPS 165

Szüksége van segítségre?

Ha segítségre van szüksége Garmin GPS 165, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Navigator Garmin

Útmutatók Navigator

Legújabb útmutatók Navigator

Alpine

Alpine CVA-1005R Útmutató

31 Március 2025
Humminbird

Humminbird 797c2 Útmutató

12 Január 2025
Navman

Navman S60 Útmutató

1 Január 2025
TomTom

TomTom Eclipse Útmutató

30 December 2025
GolfBuddy

GolfBuddy PT4 Útmutató

22 December 2024
Navman

Navman TM 550 Útmutató

14 December 2024
Navman

Navman SmartST V3 Útmutató

14 December 2024
Navman

Navman T1 Útmutató

14 December 2024