Használati útmutató Garmin GSD 24

Garmin nincs kategorizálva GSD 24

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Garmin GSD 24 (20 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 5 felhasználó értékelte átlagosan 4.2 csillagra

Letöltés PDF
Oldal 1/20
GSD 24 Transducer Adapter
Installation Instructions
About the GSD 24 Transducer Adapter
WARNING
See the Important Safety and Product Information guide in the GPS device
product box for product warnings and other important information.
Notice
The GSD 24 adapter is not meant for use with a Garmin differential 8-pin
transducer. Do not cut a Garmin differential 8-pin transducer; instead, plug it
directly into the GSD 24 according to the .GSD 24 Installation Instructions
Use this adapter to connect a non-differential transducer, such as a legacy
Garmin/Airmar® 6-pin transducer, to a GSD
™ 24 sounder. In order to adapt
a non-differential transducer for use with a Garmin differential sounder, you
must cut the connector from your existing non-differential transducer and
connect the wires to the wire block inside the GSD 24 Transducer Adapter by
following these instructions.
Tools Needed
• Drill and 1/8 in. (3.2 mm) drill bit
• #2 Phillips screwdriver
• 3mmatscrewdriver
• Cable ties (optional)
• Wire cutter
• Wire stripper
• 13/16 in. (21 mm) wrench
Mounting the Adapter
Selecting a Mounting Location
Consider the following conditions when choosing a location to mount the
GSD 24 Transducer Adapter.
• The adapter cable should easily reach the transducer connector on the
GSD 24 when mounted.
The adapter cable length is 24 in. (60.1 cm).
• The adapter should not be installed in a location where it is submerged in
water.
• The adapter should be located at least 6 in. (15.25 cm) from electrical
interference such as a motor.
• If there is not a mounting surface suitable for using the included screws,
the adapter can be secured to a structure using cable ties (not included).
Fastening the Adapter to the Mounting Location
1. Use the included template ( ) to mark the pilot-hole locations.page 19
2. Drill the two pilot holes with a 1/8 in. (3.2 mm) drill bit.
3. Installtheincludedscrewsinthepilotholes,butdonottightenthemush
with the surface.
4. Place the GSD 24 adapter on the screws and slide it in place.
5. Tighten the screws until the device is securely fastened to the surface.
Note:YoumaynditeasiertoconnectthewireswiththeGSD24
adapter unmounted, and then complete the mounting process.
Connecting a Legacy Transducer to the Adapter
Notice
The GSD 24 adapter is not meant for use with a Garmin differential 8-pin
transducer. Do not cut a Garmin differential 8-pin transducer; instead, plug it
directly into the GSD 24 according to the .GSD 24 Installation Instructions
Preparing the Legacy Transducer
1. Cut the connector from a non-differential transducer
➊
, as close to the
connector as possible.
➊
➋
➌
➍
2. Feed the cut end of the cable through the nut
➋
on the side of the housing
and pull it through the other side.
Do not tighten the nut at this time.
3. Use the wire stripper to remove about 3
1/2 in. (90 mm) of the outer cable
jacket
➌
and foil shield.
4. Use the wire stripper to remove about
1/4
in. (6 mm) of the insulation from
each internal wire
➍
.
Tinning each of the stripped wires is recommended, but not necessary.
Connecting the Legacy Transducer Wires
Connectthewirestothewireblockintheadapterusinga3mmat
screwdriver.
Consultthewiringtablewhenconnectingthewires.Specicexamplesof
many Garmin/Airmar transducer wire colors are provided on page 2.
Wire Block
Number
Wire Function
1 Depth +
2 Depth -
3 Shield
4 Ground
5 Temp*
6 XID
7 Speed power
8 Speed data
*If your transducer does not have temperature capability, you must install
a jumper between connectors 4 and 5 on the wire block.
Finalizing the Connection
1. After all the wire connections are secure, use a
13
/16 in. (21 mm) wrench to
tighten the nut around the transducer cable.
When tightened correctly you will not be able to pull the transducer cable
out of the housing.
2. Place the lid on the adapter and secure it with the four captive Phillips
screws.

Termékspecifikációk

Márka: Garmin
Kategória: nincs kategorizálva
Modell: GSD 24

Szüksége van segítségre?

Ha segítségre van szüksége Garmin GSD 24, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Garmin

Garmin

Garmin Spectra LC102 Útmutató

10 Január 2025
Garmin

Garmin Spectra LC302 Útmutató

10 Január 2025
Garmin

Garmin dēzl Headset 210 Útmutató

1 Január 2025
Garmin

Garmin GDT 43 Útmutató

14 Október 2024
Garmin

Garmin GMM 170 Útmutató

5 Október 2024
Garmin

Garmin GMR 18 xHD Útmutató

5 Október 2024
Garmin

Garmin Edge Power Mount Útmutató

3 Október 2024
Garmin

Garmin GT30-TH Útmutató

3 Október 2024
Garmin

Garmin Panoptix PS60 Útmutató

2 Október 2024
Garmin

Garmin GPS 17HVS Útmutató

30 Szeptember 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025