Használati útmutató Genie GCB01HD

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Genie GCB01HD (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
GCB01HD
HD Ground Loop Isolator
User Manual
GCB01HD - HD Ground Loop Isolator
2
1. Introduction
2. Key Features
2. Technical Specication
3. Board Diagram
The GCB01HD is a passive high efcient and reliable ground loop isolator for HDCVI / HDTVI / AHD /
Analogue Video Signal over Coaxial Cable. It’s magnetic isolation technology adoption can effectively
solve the interference issues caused by different ground potential during the signal transmission, which
improves the video anti-interference capability and effectively eliminate tearing and scrolling pictures. The
devices embedded lightning protection system improves the stability.
Passive, No Power Required
Eliminate Video Distortion caused by Ground Loops Circuit
Eliminate issues such as Image Tearing, Cross-Talk, Rolling etc.
Fully Compatible with HDCVI, HDTVI, AHD, Analogue Video Signals
Built-In 800v Insulated Voltage
Excellent Anti-interference Capability, Superior Lighting-Protection, ESD and EFT Capability
Support Unibody, with Small Volume
Model Number GCB01HD
Insertion Loss 0.5dB
Frequency Response 5Hz-70MHz
Input Impedance 75Ω
Output Impedance 75Ω
Isolation Voltage 800V (Minimum)
Isolation Resistance 100M Ω
Surge Protection Level3 Per IEC61000-4-5
ESD Protection Contact Discharge: 6KV, Air Discharge: 8KV, Per IEC61000-
4-2
Operation Temperature -10℃ ~ 55
Storage Temperature -40℃ ~ 85
Humidity 0~95% (Non-Condensing)
Dimensions (L × W × H) 41 x 24.5 x 21.6 mm
Weight 51g
*Design and Specications are subject to change without notice.
BNC Female Input BNC Male Output
GCB01HD - HD Ground Loop Isolator 3
4. Application Diagram
5. Installation Steps
6. Troubleshooting
1. Turn off the power supply of all the related devices before the installation to prevent damage to the
product.
2. Check if the coaxial cable and other transmission lines are occupied by other devices.
3. Connect the Male BNC of the device to the NVR.
4. Connect the Female BNC of the device to the camera with coaxial cable.
5. Check if the device is working and that the installation is correct. Make sure all connections are
reliable.
6. Power on the system.
7. Make sure the system can work regualrly.
Please follow below if the device doesn’t work:
Please make sure you have followed the instruction to install the device.
The transmission distance depends on the signal source and cable quality, please do not exceed the
maximum transmission distance.
Please replace a failure device with a proper one to check if the device is damaged.
If the problem still exists, please contact the dealer.
NOTE
Please use RG59 or above Coaxial Cable or CAT5e/6 Cable to reach the longest transmission distance.
LCD
Monitor
NVR
GCB01HD
Camera Coaxial Cable

Termékspecifikációk

Márka: Genie
Kategória: nincs kategorizálva
Modell: GCB01HD

Szüksége van segítségre?

Ha segítségre van szüksége Genie GCB01HD, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Genie

Genie

Genie M75 Útmutató

2 Január 2025
Genie

Genie ML90 Útmutató

2 Január 2025
Genie

Genie MP55 Útmutató

2 Január 2025
Genie

Genie ML105 Útmutató

2 Január 2025
Genie

Genie ML95 Útmutató

5 December 2024
Genie

Genie GT 06 Combo Útmutató

26 Augusztus 2024
Genie

Genie DLS5 Útmutató

19 Augusztus 2024
Genie

Genie DPS20 Útmutató

19 Augusztus 2024
Genie

Genie RC 08B Útmutató

27 Július 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025