Használati útmutató Hobbywing UBEC 5A HV (3-10S)

Hobbywing Rádióvezérlésű játékok UBEC 5A HV (3-10S)

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hobbywing UBEC 5A HV (3-10S) (1 oldal) a Rádióvezérlésű játékok kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/1

User Manual of 5A HV－

－

－－UBEC HW-SM811DUL-20130412

- 1 -

5 Amps High Voltage Switch Mode UBEC

1. Why do you need a high voltage UBEC?

The 5A-HV-UBEC is a switch-mode DC-DC regulator supplied with a 3S to 10S Lipo battery pack

and outputs a consistent safe power for your receiver, gyro and servos. It is very suitable for big

electric RC models such as fixed-wing aircrafts and helicopters which use more than 4 cells lithium

battery.

Using this UBEC, the receiver can obtain the power supply directly from the main battery pack, so

the additional battery pack for receiver is unnecessary.

Compared with the linear mode UBEC, the overall efficiency of the switch-mode UBEC is much

higher, so it can extend the working time of the receiver battery pack, and because a switch mode

UBEC can significantly reduce the heat emission, it can avoid the loss of control caused by the

over-heat problem which is frequently happened with the linear mode UBEC.

2. Specification:

2.1. Output Voltage: 5V or 6V (Changeable with an jumper )

2.2. Continuous output current: 5 Amps

2.3. Burst output current: 7.5 Amps

2.4. Input: 8V-42V (3-10 cells lithium battery pack)

2.5. Quiescent current: 20mA

2.6. Size: 48mm*27mm*9mm (length*width*height)

2.7. Weight: 30g

3. Features:

3.1. Designed with an advanced switch mode DC-DC regulator IC, the max efficiency of the chip

is up to 92%.

3.2. The output current is very large, the continuous output current is up to 5 Amps, and the

burst output current is up to 7.5 Amps.

3.3. Output short-circuits protection function.

3.4. A metal shield covers almost all the electronic components, and a filter (ferrite ring) is

attached with the output wires to significantly reduce the electromagnetic interference.

3.5. Ultra-wide input voltage from 8V-42V.

3.6. Safe power on with the polarity protection function. If the input polarity is not correct, the

UBEC can’t work, but it will not be damaged. What you need to do is just swapping the

battery pack’s polarity.

3.7. Shows the working status with an indicator (LED), it lights when the output is in normal

range.

3.8. A switch to turn on or turn off the output.

3.9. Accessory: A step-down voltage regulator with 0.7V down (from 6.0V to 5.3V)

4. Wiring

5. About RF interference

Although we have tried our best to reduce the electromagnetic interference caused by switch model

UBEC, it may still cause some interference to the receiver. So please install the filter (ferrite ring) far

away from the UBEC’s main board, and DON’T stack the filter on the main board. Please put the

whole UBEC as far as possible away from the receiver.

6. How to Use the UBEC?

6.1. Change the output voltage

The output voltage is chosen by a jumper. Please look at the upper picture, there are 3 pins at the

right corner, the upper one is Pin1, the middle one is Pin2, and the bottom one is Pin3. If the switch

is located at Pin1 and Pin2, the output is 6V. If the switch is located at Pin2 and Pin3, the output is

5V.

6.2. Working status indicator (LED)

The LED shows the status of the UBEC. When it lights, it means the UBEC has the normal output. If

it couldn’t light, please check the battery connections.

6.3. Turn on or turn off the UBEC

Push the switch to the "ON" position to turn on the UBEC; Push the switch to the “OFF" position to

turn off the UBEC.

6.4. About the 0.7V step-down voltage regulator

This 0.7V regulator is used for servos cannot work with 6V (including Futaba servo 9241, 9251,

9253, 9254, 9255, 9256 and etc). It changes the voltage from 6V to 5.3V. When the UBEC output is

set to 6V, please connect the regulator between the receiver and the above servos.

If you are using a servo can work with 6V input, the 0.7V regulator is unnecessary.

5A UBEC

5A UBEC5A UBEC Switch

Input

Output

5V Jumper for output

voltage selection

Termékspecifikációk

Márka:	Hobbywing
Kategória:	Rádióvezérlésű játékok
Modell:	UBEC 5A HV (3-10S)

Szüksége van segítségre?

Ha segítségre van szüksége Hobbywing UBEC 5A HV (3-10S), tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Rádióvezérlésű játékok Hobbywing

Hobbywing Platinum 150A V5.1 Útmutató

30 Március 2025

Hobbywing EZRUN 4278SD G2 Útmutató

30 Március 2025

Hobbywing QUICRUN 2030SL G2 6500KV Útmutató

28 Március 2025

Hobbywing QUICRUN Fusion mini16 Útmutató

28 Március 2025

Hobbywing Ezrun MAX8 G2 Útmutató

27 Március 2025

Hobbywing Xerun D10 Útmutató

27 Március 2025

Hobbywing Ezrun 3665 SD G3 Útmutató

27 Március 2025

Hobbywing Ezrun MAX10 G2 Útmutató

27 Március 2025

Hobbywing Ezrun 1626 Útmutató

27 Március 2025

Hobbywing QuicRun 2435 G2 Útmutató

27 Március 2025

Útmutatók Rádióvezérlésű játékok

Legújabb útmutatók Rádióvezérlésű játékok

Carson Easy Tyrann 550 Útmutató

1 Április 2025

E-flite Night Radian 2.0m BNF Basic Útmutató

30 Március 2025

E-flite UMX Timber X BNF Basic Útmutató

30 Március 2025

E-flite UMX Twin Otter Útmutató

30 Március 2025

E-flite Night Radian 2.0m PNP Útmutató

30 Március 2025

PowerBox Systems PBR-12X Útmutató

30 Március 2025

Amewi 22487 Útmutató

30 Március 2025

Amewi 22452 Útmutató

30 Március 2025

Amewi 22455 Útmutató

30 Március 2025

Robbe Scirocco L Útmutató

30 Március 2025