Használati útmutató Honeywell QuietSet 5 HYF260

Honeywell Ventilator QuietSet 5 HYF260

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Honeywell QuietSet 5 HYF260 (14 oldal) a Ventilator kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 4.5 felhasználó értékelte átlagosan 4.3 csillagra

Oldal 1/14
1
IMPORTANT
SAFETY
INSTRUCTIONS
READ AND SAVE THESE SAFETY
INSTRUCTIONS BEFORE USING
THIS FAN
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
FOR US MODELS ONLY – This product
employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the
product from the outlet. Replace the fuse
as per the user servicing instructions (follow
product marking for proper fuse rating)
and check the product. If the replacement
fuse blows, a short-circuit may be present
and the product should be discarded or
returned to an authorized service facility for
examination and/or repair.
1. Use this fan only as described in this
manual. Other use not recommended as
it may cause fire, electric shock or injury
to persons.
2. This product is intended for household
use ONLY and not for commercial,
industrial or outdoor use.
3. To protect against electric shock, do not
place fan in window, immerse unit, plug
or cord in water or spray with liquids.
4. This appliance has a polarized plug (one
blade is wider than the other). To reduce
the risk of shock, this plug is intended to
fit only one way in a polarized outlet. If the
plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a
qualified electrician. DO NOT attempt to
defeat this safety feature.
5. Close supervision is necessary when any
appliance is used by or near children.
6. Turn the fan OFF and unplug the fan from
the outlet when not in use, when moving
the fan from one location to another and
before cleaning.
7. To disconnect the fan, first turn the unit
OFF, grip the plug and pull it from the wall
outlet. Never pull the plug by the cord.
8. Do not use an extension cord with this fan.
9. Do not operate the fan in the presence of
explosive and/or flammable fumes.
10. Do not place the fan or any parts near
an open flame, cooking or other heating
appliance.
11. Do not operate the fan with a
damaged cord or plug or if the product
malfunctions, is dropped or damaged
in any manner (see warranty).
12. Avoid contact with moving fan parts.
13. The use of attachments not
recommended by the manufacturer
may be hazardous.
14. Place the fan on a dry level surface.
15. Do not hang or mount fan on a wall
or ceiling.
16. Do not operate if the fan housing is
damaged.
QUIETSET
®
WHOLE ROOM TOWER FAN
HYF260W Series
HYF260B Series
HYF290B Series
Owner’s Manual
Honeywell is a trademark of Honeywell International Inc., used under license by Helen of Troy Limited.
Honeywell International Inc. makes no representation or warranties with respect to this product.
QuietSet is a registered trademark owned by Helen of Troy Limited.
2 3
A. BASE ASSEMBLY
Remove 2 thumb screws from the base and set aside. Align the front and
back base pieces and gently push until pieces snap securely together
(Fig. 3).
B. SECURING THE TOWER FAN TO THE BASE
At the base of the housing, remove the locking nut and set aside.
Carefully lift the fan housing (Fig. 4) and place the power cord through
the center of the base.
• Lower the fan housing into the base (Fig. 4), align the back of
the fan with the back of the base. Gently rotate the fan housing
until it is seated in the base. (Fig. 5).
Take the locking nut and place power cord through the locking nut
(Fig 4) bringing locking nut up inside the base, (Fig. 5) screw the locking
nut onto the fan housing turning clockwise until fully tightened and an
audible ratcheting is heard.
D. SECURING THE CORD INSIDE THE BASE
Gently place the fan on its side, pressing the cord securely into cord
guides (Fig. 6) along the inside of fan base, exiting through the notched
opening (Fig. 6) ensuring a flat and stable base for the fan.
• Place 2 thumb screws into the the base for added stability (Fig. 7).
Return the tower fan to its upright position.
Note: Do not operate the tower fan unless it is in its proper,
upright position.
ASSEMBLY INSTRUCTIONS
Fig. 3
Fig. 5
Fig. 6
Fig. 4
17. A loose fit between the AC outlet
(receptacle) and plug may cause
overheating and a distortion of the plug.
Contact a qualified electrician to replace
loose or worn outlet.
18. Do not operate any fan with a damaged
cord or plug. Discard any damaged fan,
return the fan to the retailer where the
fan was purchased, or request a return
authorization to return to Kaz USA, Inc. for
examination and/or repair.
19. Do not run fan cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange
cord away from traffic areas and where it
will not be tripped over.
WARNING: To Reduce The Risk of Fire or
Electric Shock, Do Not Use This Fan With
Any Solid-State Speed Control Device,
other than the one supplied.
This fan features a fused safety plug which is designed to cut off electric current to the fan if an
electrical fault occurs. Please see below for more information on how to properly use your fan and
replace the safety plug fuse, if needed.
FUSED SAFETY PLUG - FOR US ONLY
USER SERVICING INSTRUCTIONS
If your fan loses power and you suspect that the fuse on your fan
has blown, grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
Slide fuse cover, located on the top of the plug, towards the
prongs of the plug. (Fig. 1)
Carefully remove the blown fuse and snap a new fuse into place.
To Reduce the Risk of Fire, replace fuse only with 2.5 Amp,
125 volt fuse. Fully close the fuse door by sliding back into
place. (Fig. 2) Discard the blown fuse. The plug should now
be ready for normal use.
To Reduce the Risk of Fire, do not replace attached plug.
Contains a safety device (fuse) that should not be removed.
Discard product if the attached plug is damaged.
If you need further information on how or when to replace
the fuse in the safety plug, please contact Kaz Consumer
Relations Department by visiting our website at
www.honeywellpluggedin.com/fans or calling
1-800-477-0457.
Fig. 1
Fig. 2
Fig. 7
4 5
ON/OFF
To turn fan on, press the
Power button ( ) located
on the bottom center of the control panel.
SPEED CONTROL
The fan will automatically start on “Sleep” speed when
initially turned on. To adjust the speed up or down, press
the
Fan Speed button ( ) repeatedly to increase level.
OSCILLATION
To activate the Oscillation feature, press the
Oscillation button
(
) once. Press the Oscillation button again to turn the
Oscillation feature off.
TIMER
Choose from 1, 2, 4, or 8 hour settings by performing
the following function:
1 hour: Press the
Timer button ( ) once.
2 hours: Press the
Timer button twice.
4 hours: Press the
Timer button a third time.
8 hour
s: Press the Timer button a fourth time.
Press the
Timer button a fifth time to turn the Timer feature off.
AUTO DIM LIGHT FEATURE
Control panel light automatically dims to 50% brightness after 15 seconds and
resumes to 100% brightness when settings are changed.
HYF290 SERIES FAN OPERATION
ON/OFF
Press the Power button ( ) once to turn the fan on. Press
the Power button a second time to turn the fan off.
SPEED CONTROL
The fan will automatically start on “Sleep” speed when
initially turned on. To adjust the speed up or down, press
the Fan Speed button (
) repeatedly to increase level.
OSCILLATION
To activate the Oscillation feature, press the Oscillation button
(
) once. Press the Oscillation button again to turn the Oscillation
feature off.
REMOTE CONTROL STORAGE
When it is not in use, the remote control may be stored in the recessed
area located behind the controls (Fig. 9).
HYF260 SERIES REMOTE CONTROL OPERATION
Fig. 9
REMOTE CONTROL BATTERY INSTALLATION/REPLACEMENT INSTRUCTIONS
A. Remove battery door by sliding downward in direction of arrow (Fig. 8).
B. Insert 2 AAA batteries into the remote following the directional guides
in the recessed slots. Batteries are included.
C. Replace battery door by sliding upward opposite of arrow direction
until door snaps in place.
NOTE: DO NOT MIX OLD AND NEW BATTERIES. DO NOT MIX ALKALINE,
STANDARD (CARBON-ZINC) OR RECHARGEABLE (NICKEL-CADMIUM) BATTERIES.
SEE RECYCLERS IN YOUR AREA FOR PROPER DISPOSAL OF BATTERIES.
ASSEMBLY INSTRUCTIONS
FAN OPERATIONFAN OPERATION
HYF260 SERIES FAN OPERATION
Fig. 8
Model HYF260 SERIES
Model HYF260 SERIES
in CANADA ONLY
Power Cool
Cool
Refresh
Relax
White Noise
Calm
Whisper
Sleep
1
2
4
8
Model HYF290 SERIES
1
2
4
8
Model HY290 SERIES
in CANADA ONLY
ON/OFF
To turn fan on, press the Power button ( ) located on the
bottom center of the control panel.
SPEED CONTROL
The fan will automatically start on “Sleep” speed when initially
turned on. To adjust the speed up or down, press the Fan Speed
button (
) repeatedly to increase level.
OSCILLATION
To activate the Oscillation feature, press the Oscillation
button (
) once. Press the Oscillation button again to turn
the Oscillation feature off.
TIMER
Choose from 1, 2, 4, or 8 hour settings by performing
the following function:
1 hour: Press the Timer button (
) once.
2 hours: Press the Timer button twice.
4 hours: Press the Timer button a third time.
8 hours: Press the Timer button a fourth time.
Press the Timer button a fifth time to turn the Timer feature off.

Termékspecifikációk

Márka: Honeywell
Kategória: Ventilator
Modell: QuietSet 5 HYF260

Szüksége van segítségre?

Ha segítségre van szüksége Honeywell QuietSet 5 HYF260, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek