Használati útmutató Honeywell RTH230B

Honeywell Termosztát RTH230B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Honeywell RTH230B (4 oldal) a Termosztát kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

RTH230B 69-1800 2/6/05 1/4

The RTH230B programmable thermostat can be used to control:

• a gas, fuel oil or electric furnace - 2 or 3 wires

• a central air conditioner - 2 or 3 wires

• a hot water system with or without pump - 2 wires

• a millivolt system - 2 wires

• a central heating and cooling system - 4 or 5 wires

Note: These thermostats are not compatible with heat pumps or

multi-stage systems.

Features

• System operating mode selection: heat, cool or off

• Fan operating mode selection: automatic or on (continuous)

• Programmable heating and cooling cycle lengths: 10, 12, 15, 20

or 30 minutes

• Temperature display in °F or °C

• Battery replacement indicator

• 5-2 programming including:

- Preprogrammed energy-saving schedule

- Early Start

- Temporary bypass

- Time display (12 h or 24 h)

• Filter replacement indicator

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT

POWER TO THE HEATING SYSTEM.

nRemove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,

it was probably powered by 120/240 volts. In this case, this thermo-

stat cannot be used.

oIdentify and label each wire (with the corresponding letter on

the wire terminal) and remove them from the terminals.

pIf necessary, strip the end of each wire (maximum of 1/4 inch).

qWrap the wires around a pencil to prevent

them from falling into the wall.

rIf the hole in the wall is too big, insulate it

using a non-flammable material in order to

avoid air draughts behind the thermostat.

For a new installation, choose a location approximately 5 feet

(1.5 m) above the floor and on an inside wall. Avoid draughty

areas (top of staircase, air outlet, etc.), dead air spots (behind

doors), direct sunlight or areas near concealed pipes or chim-

neys.

nRemove the thermostat faceplate.

oLoosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

pTilt the thermostat upwards.

qMark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

rPass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

The connection of the new thermostat should be similar to that of

the old thermostat; however, it can vary depending on the installa-

tion.

Note: The red jumper wire between the Rc and Rh terminals must

be removed in 2- or 5-wire installations. The jumper must be used in

3- or 4-wire installations if you wish to use the mode selector switch

for the fan.

Display Adjustment

buttons

System operating

mode selector Fan operating

mode selector

Programming

buttons

Rh Heating power supply

Rc Cooling power supply

W Heating signal

Y Cooling signal

G Fan

RTH230B 69-1800 2/6/05 2/4

The jumper defines the fan operation when the fan is placed in auto-

matic mode.

nPull out the battery cover.

oInstall the batteries as shown. Observe the polarity.

pReinstall the battery cover. You will hear a clicking sound.

After the batteries are installed, the thermostat performs a series of

tests for approximately 5 seconds.

Afterwards, the screen displays the actual

temperature. It is normal that the displayed

temperature be higher than the ambient

temperature if you are holding the thermo-

stat. The thermostat will display the ambient temperature once it is

installed on the wall. By default, the setpoint is 70°F (21°C).

nOnce the baseplate and the batteries are installed, mount the

thermostat on the baseplate.

oSecure the thermostat using the locking screw and install the

faceplate.

pApply power back to the system.

Use the selector switch to place the system in Heating

mode (HEAT) or Cooling mode (COOL), or to set the

system off.

Note: When you place the thermostat in Cooling mode, you might need to

wait up to five minutes before cooling can start. This is a safety feature for

the compressor. will flash on the screen until cooling can start again.

Use this setting if you have an electric furnace. In

this setting, when the fan is placed in automatic

mode, it works only when heating or cooling is

activated.

Use this setting if you have a gas or fuel oil fur-

nace. In this setting, when the fan is placed in

automatic mode, it works as follows:

• When the thermostat is placed in cool mode,

the fan works only when cooling is activated.

• When the thermostat is placed in heat mode,

the fan is controlled by the furnace fan control

circuitry.

J2 jumper

RTH230B 69-1800 2/6/05 3/4

Use the selector switch to set the fan to automatic

mode (AUTO) or continuous mode (ON).

Note: This switch is not used if you have a 2-wire

installation as the fan is not connected to the thermo-

stat.

The actual temperature is normally displayed. To view the setpoint,

press once on one of the buttons. The setpoint is displayed for

5 seconds along with the icon.

Note: Pressing either of the buttons more than once will

change the setpoint.

Press one of the buttons until the desired temperature is dis-

played.

Maintains the temperature at a fixed setpoint. To place the thermo-

stat in this mode, press [ Mode ]. The house icon will disappear.

Maintains the temperature according to the energy-saving sched-

ule. To place the thermostat in this mode, press [ Mode ]. The cur-

rent period will be displayed. The four possible periods are:

To see the default settings of each period, see section 5.2.

Temporary Bypass

If you modify the temperature (using the buttons) when the

thermostat is in programmable mode, the new temperature will be

used for the next 2 hours. The house icon flashes during the

bypass. At the end of the bypass period, the thermostat returns to

the temperature settings of the period currently underway.

After 500 hours of operation, an icon appears to indi-

cate that the filter needs replacement. Once the filter

is replaced, press [ Filter ] for 3 seconds to remove

the icon and reset the counter.

An icon appears when the batteries need replacement.

This icon will flash for 120 days, then the thermostat

will cut power to the heating/cooling unit. The icon dis-

appears once the batteries are replaced.

After replacing the batteries, readjust the time and day (see section

5.1). However, the temperature and program settings are saved and

do not need to be re-entered.

Warning: Before removing the batteries, place the

system switch on the thermostat to Off. Otherwise, the

heating/cooling unit might still be running even after

the batteries are removed.

nTo access the configuration menu, press both buttons

simultaneously for 3 seconds.

oTo go to the next parameter (menu item), briefly press both

buttons simultaneously.

pTo modify a parameter, press one of the buttons.

qRepeat steps 2 and 3 if necessary.

rPress both buttons simultaneously for 3 seconds to exit

the configuration menu.

nPress [ Clk ]. The hour flashes.

oSet the hour using .

pPress [ Clk ]. The minutes flash.

qSet the minutes using .

rPress [ Clk ]. The day flashes.

sSet the day using .

tPress [ Exit ] to exit.

AUTO

• If you have an electric furnace (see section 2.4), the fan

works only when heating or cooling is activated.

• If you have a gas or fuel oil furnace (see section 2.4), the fan

works as follows:

• When the thermostat is placed in cool mode, the fan

works only when cooling is activated.

• When the thermostat is placed in heat mode, the fan is

controlled by the furnace fan control circuitry.

ON The fan is always on.

Wake up Leave for work Return home Sleep

DISPLAY DESCRIPTION DEFAULT OPTIONS

Temperature display °F °C or °F

Time display 12 h 12 h or 24 h

Early Start 1 Off On or Off

Heating cycles per hour

242, 3, 4, 5 or 6 3

Cooling cycles per hour 242, 3, 4, 5 or 6 4

1 When Early Start is On, the thermostat determines when to start heating

or cooling so that the desired temperature is reached at the set time.

2 When either the heating or cooling parameter is displayed, use the sys-

tem mode selector switch to alternate between the two parameters.

3 For optimal heating control, use the setting that matches your system as

follows: 2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-effi-

ciency furnace), 4=15 min (gas or oil), 5=12 min (alternate setting for gas

or oil), 6=10 min (electric).

4 The corresponding cooling cycle lengths are as follows: 2=30 min,

3=20 min, 4=15 min, 5=12 min, 6=10 min

Termékspecifikációk

Márka:	Honeywell
Kategória:	Termosztát
Modell:	RTH230B

Szüksége van segítségre?

Ha segítségre van szüksége Honeywell RTH230B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Termosztát Honeywell

Honeywell T87M1011 Round Modulation Útmutató

3 Április 2025

Honeywell Chronotherm Modulation - T8851 Útmutató

26 Március 2025

Honeywell Round on Útmutató

16 Január 2025

Honeywell CM 921 Útmutató

16 Január 2025

Honeywell T87HC - Round Heat Cool Útmutató

16 Január 2025

Honeywell off Útmutató

16 Január 2025

Honeywell Round Wireless Modulation - Y87RF1004 Útmutató

15 Január 2025

Honeywell Day Night Round T8700A Útmutató

4 Október 2024

Honeywell Round on-off T87G1006 Útmutató

4 Október 2024

Honeywell CM5000 Útmutató

29 Szeptember 2024

Útmutatók Termosztát

Legújabb útmutatók Termosztát

Amfra Thermic Control 77 Útmutató

9 Április 2025

UPM THM101A Útmutató

7 Április 2025

Jablotron TP-80 Útmutató

7 Április 2025

Eberle INSTAT 868-a6 Útmutató

6 Április 2025

Theben RAMSES 818 top 6A Útmutató

6 Április 2025

Sorel RC21 Útmutató

6 Április 2025

Hoffman ATEMNO Útmutató

5 Április 2025

Vaillant VRC calormatic UBW Útmutató

4 Április 2025

Eberle RTR-E 6145 Útmutató

4 Április 2025

Eqiva CC-RT-Q Útmutató

3 Április 2025