Használati útmutató HP TFT5600

HP Monitor TFT5600

Olvassa el alább 📖 a magyar nyelvű használati útmutatót HP TFT5600 (3 oldal) a Monitor kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

hp TFT5600

rackmount keyboard

and monitor

installation instructions

Read Instructions Completely

Before Beginning Installation Procedures

Hewlett-Packard Company shall not be liable for technical or editorial errors or

omissions contained herein. The information in this document is provided “as is”

without warranty of any kind and is subject to change without notice.

The warranties for HP products are set forth in the express limited warranty

statements accompanying such products. Nothing herein should be construed as

constituting an additional warranty.

Second Edition (September 2002)

Part Number 230201-022

230201- 022

About this Device

The TFT5600 Rackmount Keyboard and Monitor (RKM) is a

rack-mountable 1U integrated flat panel monitor, with a 15-inch

(38.1 cm) color active matrix Thin Film Transistor (TFT) Liquid

Crystal Display (LCD), and keyboard with hot keys and track ball.

NOTE: 1U= 1.75 inches or 44.45 cm

The TFT5600 RKM is mounted on rails with space to add the HP

1U switch box behind the unit. The TFT5600 RKM can be used

with all Compaq 9000 Series racks and HP 10000 Series racks.

Kit Contents

Below are the items and quantities required for assembly:

• M-6 cage nuts (2)

• M-6 screws (8)

• 6-32 screws (12)

• Mounting rails with slide (2)

• Cable management arm (1)

• Brace (1)

• TFT 5600 RKM (1)

• Lock plate (2)

• Rack template (1)

This kit may contain extra pieces of hardware for your

convenience.

Optional Equipment

• Video Connector Adapter Option Kit (Part number

149361-B21)—The video connector adapter provides an

interface for video connectors that are missing pin 9.

Tools Required

• Phillips screwdriver

• T-15 Torx driver

Rack Considerations

Before beginning these procedures, make sure you understand and

follow these precautions:

WARNING: To reduce the risk of personal injury or damage to

the equipment, be sure that:

• The leveling jacks are extended to the floor.

• The full weight of the rack rests on the leveling jacks.

• The stabilizing feet are attached to the rack, if it is a

single-rack installation.

• The racks are coupled in multiple-rack installations.

• Only one component is extended at a time. A rack may

become unstable if more than one component is extended

for any reason.

Installing the TFT5600 RKM

1. Determine the appropriate rack position for the TFT5600

RKM, generally 20U or user preference.

Measuring from the top of the component, use the template on

the front and rear of the rack frame to mark the attachment

points for the mounting brackets and rear cage nuts.

NOTE: When using the template on the back of the rack, mark the rack at

the top of the template to help align the next component.

2. Install the mounting rails with slides.

a. Insert one cage nut (1) into the hole marked with the rack

template on the rear of the rack.

b. Hook the tabs on the mounting rail into the appropriate

holes on the rear of the rack, and insert one screw (2).

IMPORTANT: Be sure to align the front screw holes when attaching the

mounting rail to the rear of the rack.

c. Insert two M-6 screws into the holes at the front of the rack,

and then tighten (3).

d. Repeat steps 2a through 2c to install the other

mounting rail.

3. Attach the brace assembly to each mounting rail with the cable

access hole facing the right side of the rack.

NOTE: Make sure the cable access hole is positioned on the right, to allow

appropriate routing of cables.

a. Flex the rail out slightly to allow the brace to be inserted.

Align the screw holes on the brace with the screw holes on

the rails (1).

b. Insert one 6-32 screw (2) on each side.

c. Tighten the screws (3).

4. Attach the cable management arm to the right corner of the

brace and secure it with two 6-32 screws.

5. Install the tray assembly.

a. Fully extend the sliding rails until locked (1).

b. Place the tray assembly on the rails, aligning the screw

holes on the tray with the tabs on the rails (2).

c. Secure with two 6-32 screws on each side (3).

6. Attach the cable management arm to the rear of the tray with

two 6-32 screws.

7. Carefully route the keyboard power and video cables into the

cable management arm. Then route the cables through the

mounting rail opening.

8. Place the tray back into the rack.

a. Slide the locking bar (1) to unlock.

IMPORTANT: If the TFT5600 RKM is not properly aligned with other

rack-mounted devices when installed, cosmetic damage to the top of the

unit can occur due to interference. Leave protective sheet on the unit

while adjusting.

b. Carefully push the tray (2) into the rack.

IMPORTANT: If the TFT5600 RKM interferes with the other rack-mounted

devices, above or below, loosen the M-6 screws on the mounting rails to

make appropriate adjustments.

Installation is complete.

Termékspecifikációk

Márka:	HP
Kategória:	Monitor
Modell:	TFT5600

Szüksége van segítségre?

Ha segítségre van szüksége HP TFT5600, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Monitor HP

HP Pavilion 2211x Útmutató

20 Március 2025

12 Január 2025

31 December 2025

31 December 2025

31 December 2025

31 December 2025

31 December 2025

31 December 2025

22 December 2024

22 December 2024

Útmutatók Monitor

Legújabb útmutatók Monitor

NEC SpectraView II Útmutató

9 Április 2025

Asus VA279QGS Útmutató

9 Április 2025

Acer EV227Q Útmutató

9 Április 2025

BenQ PD3226G Útmutató

8 Április 2025

BenQ DesignVue PD2730S Útmutató

8 Április 2025

Samsung LH65QETEPGC Útmutató

5 Április 2025

Gigabyte MO27U2 Útmutató

5 Április 2025

Philips 221V8LB Útmutató

4 Április 2025

PureTools PT-SCREEN-100 Útmutató

2 Április 2025

Extron TLS 1025M Útmutató

2 Április 2025