Használati útmutató Humminbird HELIX 7 CHIRP MEGA DI GPS G4N CHO
Humminbird
halkereső
HELIX 7 CHIRP MEGA DI GPS G4N CHO
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Humminbird HELIX 7 CHIRP MEGA DI GPS G4N CHO (13 oldal) a halkereső kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 6 felhasználó értékelte átlagosan 4.8 csillagra
Oldal 1/13
1
532405-6_B
HELIX® SERIES CONTROL HEAD Installation Guide
Follow the instructions in this installation guide to gimbal mount the control head.
NOTE: Your gimbal bracket may not look exactly like the gimbal bracket shown in the illustrations, but it will mount in exactly the same way.
Installation Preparation
Read the instructions in this transducer guide completely to understand the mounting guidelines before starting the installation.
Visit our Web site at humminbird.com for additional information and resources for transducer installations. Also, visit
youtube.com/humminbirdtv for informational videos.
Supplies: In addition to the hardware supplied with your control head, you will need a powered hand drill and various drill bits, Phillips
head screwdriver, flat head screwdriver, pencil, safety glasses and dust mask, marine-grade silicone sealant, dielectric grease
(optional), extension cables (optional), Ethernet cables (optional), and accessory cables (optional). Also, see Connect Power to
determine the type of connection, fuse size, and additional equipment you will need for the installation.
Accessories and Ethernet: Accessories and Ethernet equipment are available for purchase at . The installation humminbird.com
guides are available with the product, or they can be downloaded from our Web site.
Installation Overview
1 | Plan the Mounting Location
1. Place 1 rubber washer onto each gimbal knob.
2. Install the gimbal knobs (with washers) into each side of the control head. Tighten the knobs just enough so you can slide the control
head into the gimbal bracket arms.
Assembling the Control Head and Bracket
gimbal
knob
bracket arm
rubber
washer
NOTE: If you prefer to mount the control head overhead, flip the bracket to the top of the control head. The opening in the gimbal bracket arms
must face the rear of the control head.
3. Place the assembled control head in various locations to determine the best mounting location with the following requirements:
∆a stable, protected surface to protect the control head from excessive wave shock, vibration, and water
∆sufficient space for the control head tilt range
∆visibility during operation, as well as easy installation and removal
∆access above and below the mounting surface to pass the cables through to the control head
∆space for the 1" (25 mm) cable hole located 2" to 4" (50 to 100 mm) behind the chosen mounting location
4. Test route all cables (transducer, power, Ethernet, accessories) to the control head mounting location. Leave enough cable length for
installing the cable tray and for the control head tilt range.
5. After you have selected the mounting location, loosen the gimbal knobs and remove the control head from the gimbal bracket.
Termékspecifikációk
| Márka: | Humminbird |
| Kategória: | halkereső |
| Modell: | HELIX 7 CHIRP MEGA DI GPS G4N CHO |
Szüksége van segítségre?
Ha segítségre van szüksége Humminbird HELIX 7 CHIRP MEGA DI GPS G4N CHO, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók halkereső Humminbird
8 Október 2024
24 Augusztus 2024
20 Augusztus 2024
20 Augusztus 2024
20 Augusztus 2024
20 Augusztus 2024
20 Augusztus 2024
14 Augusztus 2024
13 Augusztus 2024
3 Augusztus 2024
Útmutatók halkereső
- halkereső Garmin
- halkereső Raymarine
- halkereső Lowrance
- halkereső Closer Pets
- halkereső Deeper
- halkereső Lucky
- halkereső Eagle
- halkereső Simrad
- halkereső Furuno
Legújabb útmutatók halkereső
12 Január 2025
1 Január 2025
30 December 2025
21 Szeptember 2024
19 Szeptember 2024
15 Szeptember 2024
5 Szeptember 2024
23 Augusztus 2024
23 Augusztus 2024
21 Augusztus 2024