Használati útmutató IFi Audio Hip dac 3
IFi Audio
nincs kategorizálva
Hip dac 3
Olvassa el alább 📖 a magyar nyelvű használati útmutatót IFi Audio Hip dac 3 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 18 ember találta hasznosnak és 9.5 felhasználó értékelte átlagosan 5.0 csillagra
Oldal 1/2
8. USB-C data input port
Connect your phone to the hip dac 3 with a Lightning to USB
Camera Adapter (Apple) or USB-C to USB-C cable (Android).
When using other audio sources, please connect with a USB
cable. This USB-C port is intended for data transfer only.
Tip: For Apple iOS and Android devices, please use battery power on the hip dac 3,
otherwise you may receive error messages from your device.
Note: For use with PC it is necessary to download drivers.
Tip: For the required driver and all the latest firmware updates please refer to our
website: www.ifi-audio.com/download-hub/
9. USB-C (5V) battery charge input
For charging only. It will take ~3 hours for a high-powered USB
charger to fully charge hip dac 3. Use the enclosed USB 'Type A'
to 'Type C' cable, smart charger or a regular charger up to 6.3V.
10. LED for Battery Status
LED Status
White* > 75%
Green* 25% >
Red* 10% >
Red (flashing) 10% ≤
*Battery LED will flash when it is charging
ifi-audio.com
Ver1.0
31 2 5 64
4. ON/OFF and Analogue Volume Control
The analogue volume control in hip dac 3 is superior to any digital
volume control.
Warning: Due to the high power of hip dac 3, always start off at a low volume level
so that there is no risk of damage to your headphones and your hearing. iFi audio is
not responsible for any hearing or equipment damage from misuse.
Power ON. Power OFF.
Tip: hip dac 3 will continue to use battery power even if the USB cable is connected
afterwards.
Tip: For connection to Apple devices, Apple Lightning to USB Camera Adapter is
required. For connection to Android devices, USB-C to USB-C cable and
appropriate OS support are required.
For more information, please refer to www.ifi-audio.com
5. Balanced 4.4mm headphone output
Connect balanced 4.4mm headphones.
6. S-Balanced 3.5mm headphone output
Connect 3.5mm headphones.
7. iEMatch switch
iEMatch reduces the output level, so that even the most
sensitive In-Ear-Monitors (IEMs) can be matched to the hip dac 3.
= 3.5mm headphones
= off
= 4.4mm headphone
Tip: The hip dac 3 or the headphone will not be damaged if the iEMatch switch is adjusted incorrectly,
but the attenuation level will not be correct.
98 10
OFF
1. PowerMatch (on/off )
PowerMatch enables hip dac 3 to match headphones' impedance
and sensitivity in order to generate their highest operational
efficiency.
Tip: For in-ear-monitors (earbuds) try PowerMatch off. For headphones try PowerMatch on,
When on, the gain increases by 10dB. If your IEMs are very sensitive, try using the iEMatch
feature (item 7).
2. XBass (on/off)
Many headphones lack the correct bass response. XBass is an
analogue circuit designed to 'add back' the lost bass response for a
more accurate reproduction of the original music.
3. Audio Format LED (kHz)
The LED colour scheme indicates the audio format and sampling
frequency received by hip dac 3 from the music source.
LED Mode
Yellow PCM 44.1/48kHz
White PCM 88.2/96/176.4/192/352.8/384kHz
Cyan DSD 64/128
Red DSD 256
Green MQA
Blue MQA Studio
Magenta Original Sample Rate*
*MQB
Warning: Installing GTO enabled firmware may result in the LED's on this device no longer
changing in accordance with the above table
7
iE Ma tc h
of f
3. 5
4. 4
SPECIFICATIONS
Input: USB-C
Formats supported: DSD256 / 11.3MHz
PCM 384kHz
full MQA Decoder
DAC: Bit-Perfect DSD & DXD DAC by Burr Brown
Headphone Outputs:
Balanced 4.4mm
S-BAL 3.5mm
Power Output:
Balanced 400mW @ 32 ; 6.3V @ 600Ω Ω
S-BAL 280mW @ 32 ; 3.2V @ 600Ω Ω
Output Impedance:
Balanced ≤1 , With iEMatch engaged: ≤4.5Ω Ω
S-BAL ≤1 , With iEMatch engaged: ≤4.5ΩΩ
SNR:
Balanced ≥109dB(A) @ 0dBFS
S-BAL ≥103dB(A) @ 0dBFS
DNR:
Balanced ≥109dB(A)
S-BAL ≥103dB(A
THD + N:
Balanced <0.006X% (360mW/2.0V @ 600Ω)
S-BAL <0.01% (100mW/1.27V @ 16Ω)
Frequency Response: 20Hz - 45kHz (-3dB)
Power Consumption: <2W idle, 4W max
Battery: Lithium-polymer 2200mAh approx.
8 hours
Power System: Charging via USB-C,BC V1.2 compliant up
to 1000mA charging current
Dimensions: 102 x 70 x 14 mm (4.0" x 2.8" x 0.6")
Net weight: 135 g (0.30 lbs)
Limited Warranty: 12 months*
*12 months typical or as permitted/required by local reseller laws.
**Specifications are subject to change without notice.
Termékspecifikációk
| Márka: | IFi Audio |
| Kategória: | nincs kategorizálva |
| Modell: | Hip dac 3 |
Szüksége van segítségre?
Ha segítségre van szüksége IFi Audio Hip dac 3, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók nincs kategorizálva IFi Audio
14 Január 2025
14 December 2024
19 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
2 Szeptember 2024
Útmutatók nincs kategorizálva
- nincs kategorizálva Sharper Image
- nincs kategorizálva Bauknecht
- nincs kategorizálva After Later Audio
- nincs kategorizálva Séura
- nincs kategorizálva Mellerware
- nincs kategorizálva Premier
- nincs kategorizálva BeamZ
- nincs kategorizálva Parklands
- nincs kategorizálva Lifan
- nincs kategorizálva Swann
- nincs kategorizálva Harvia
- nincs kategorizálva Bixolon
- nincs kategorizálva LandRoller
- nincs kategorizálva SKLZ
- nincs kategorizálva Cambium Networks
Legújabb útmutatók nincs kategorizálva
10 Április 2025
10 Április 2025
10 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025
9 Április 2025