Használati útmutató Indesit WIDXXL 146

Indesit Szárítógép WIDXXL 146

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Indesit WIDXXL 146 (72 oldal) a Szárítógép kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/72

Instruction booklet

WASHER DRYER

WIDXXL 146

English

Contents

Installation, 2-3

Unpacking, 2

Remove the transit fixings, 2

Levelling, 2

Water connection, 2

Drainage & connections, 3

The first wash cycle, 3

Technical Details, 3

Washer Dryer description, 4-5

Control panel, 4

LEDs, 5

Starting and programmes, 6

Briefly: starting a programme, 6

Programme table, 6

Personalisation, 7

Setting the temperature, 7

Setting the drying cycle, 7

Options, 7

Table of drying times, 7

Detergents and laundry, 8

Detergent dispenser, 8

Preparing your laundry, 8

Precautions and advice, 9

General safety, 9

Saving energy and respecting the environment, 9

Disposal, 9

Care and Maintenance, 10

Switching off the water or electricity supply, 10

Cleaning, 10

Caring for your appliance door and drum, 10

Checking the water inlet hose, 10

Troubleshooting, 11

Service, 12

Before calling for assistance, 12

Spare Parts, 12

Tr7003gb_WIDXXL146.p65 27/01/06, 8.301

! Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washer dryer to inform the

new owner as to its operation and features.

! Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking

1. Unpack the machine.

2. Check whether the machine has been damaged

during transport. If this is the case, do not install it and

contact your retailer.

Remove the transit fixings

IMPORTANT: Follow these instructions to remove the

TWO transit fixings.

Situated on either side of the

rear panel, BOTH transit boltsBOTH transit bolts

BOTH transit boltsBOTH transit bolts

BOTH transit bolts

MUST be rMUST be r

MUST be removed beforemoved befor

emoved beforemoved befor

emoved before usee use

e usee use

e use.

! Failure to do so may cause

damage to your machine.

It is important the transit bolt

and spacer (see pic) come out

intact.

1. Unscrew the bolt using a

13mm spanner.

2. STOP when 3 threads can be

seen.

3. Hold, slide sideways and pull

to remove.

4. For safety, insert one of the

two plastic covers (supplied

with your machine) over the

hole.

! Repeat steps 1 to 4 to remove

the second transit bolt.

! Packaging materials are not

children’s toys.

Levelling

Your machine will be noisy if the two front feet are not

adjusted so that the machine stands firm and level.

! The machine should be levelled from side to side and

from front to back.

1. Move your machine into its final location.

- Take care not to trap or kink the hoses.

2. Turn one or both front feet

anti-clockwise by hand until the

feet cannot be turned any

more.

When adjusting the feet, use a

spirit level to check the machine

stands level, from side to side

and from front to back.

- The spring on each foot will stop them coming

loose.

! If it is placed on a fitted or loose carpet, adjust the

feet in such a way as to allow enough room for

ventilation beneath the machine.

Water connection

Connecting the water inlet hose.

Remember that this is a cold-fill machine.

! Check that seal is in place

inside the hose end cap.

Before making the water connections to gas ¾

thread, allow the water to run freely from the supply

tap until it is perfectly clear.

Screw the inlet end with the

blue cap onto the cold water

supply tap.

Turn the taps on and check for leaks: tighten if

necessary.

! Make sure there are no kinks or bends in the

hose.

! The water pressure at the tap must be within the

values indicated in the Technical details table (next

page).

! If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

! Always use new hoses.

! Check the water hose at least once a year, replace

any that are cracked as worn hoses could split under

water pressure.

Installation

Tr7003gb_WIDXXL146.p65 27/01/06, 8.302

Drainage connections

A. Connect the drain

hose, without kinking it,

to a draining duct or a

wall drain fixed at a

height between 65 and

100cm from the floor.

B. Alternatively, place it

over the edge of a

basin, sink or tub,

fastening the hose

supplied to the tap.

! The free end of the hose should not be under

water.

! We advise against the use of hose extensions. In

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150cm in length.

Electrical connections

Before plugging the appliance into the mains socket,

make sure that:

• the socket is earthed and in compliance with the

applicable law.

• the socket is able to sustain the appliances

maximum power load indicated in the Technical

Details table (on the right).

• the supply voltage is included within the values

indicated in the Technical Details table (on the

right).

• the socket is compatible with the machine’s plug.

If this is not the case, replace the socket or the

plug.

! The machine should not be installed in an outdoor

environment, not even when the area is sheltered,

because it may be very dangerous to leave it

exposed to rain and thunderstorms.

! When the machine is installed, the mains socket

must be within easy reach and should be connected

to a suitable electrical supply.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by

an authorised serviceman.

! The company denies all liability if and when these

norms are not respected.

The first wash cycle

Once the appliance has been installed and before

you use it for the first time, run a wash cycle without

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

Tr7003gb_WIDXXL146.p65 27/01/06, 8.303

TECHNICAL DETAILS

Model WIDXXL 146

Dimensions 59.5 cm wide

85 cm high

52.5 cm deep

Capacity from 1 to 7 kg

Electric

connections

voltage 220 - 240 volts 50 Hz

Absorbed power 1700 - 2100 W

Water

connection

maximum pressure 1 MPa (10 bar)

minimum pressure 0,05 MPa (0,5 bar)

drum capacity 54 litres

Spin speed up to 1400 rpm

Control

programmes

according to

the IEC456

directive

programme 2*

Wash run with a 7 kg load

Dry run with 5 kg and 2 kg loads

*set wash temperature to 60°C

This appliance is compliant with the

following European Community

directives:

- 72/23/CEE of 19/02/73 (Low Voltage)

and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

Termékspecifikációk

Márka:	Indesit
Kategória:	Szárítógép
Modell:	WIDXXL 146

Szüksége van segítségre?

Ha segítségre van szüksége Indesit WIDXXL 146, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Szárítógép Indesit

Indesit YT M11 92B X Útmutató

7 Január 2025

Indesit YT M11 82SS X Útmutató

7 Január 2025

Indesit C YD A81 WWGL UK Útmutató

7 Január 2025

Indesit YT M11 82B X UK Útmutató

2 Január 2025

Indesit IDV 75 B K (UK) Útmutató

14 Október 2024

Indesit YT M11 82 X UK Útmutató

14 Október 2024

Indesit Ecotime IWDC 65125 S UK Útmutató

9 Október 2024

Indesit BDE 961483X W UK Útmutató

3 Október 2024

Indesit EDCE 85 B TM Útmutató

2 Október 2024

Indesit IDC 8T3 B (UK) Útmutató

22 Szeptember 2024

Útmutatók Szárítógép

Legújabb útmutatók Szárítógép

Bauknecht traa prestige Útmutató

10 Április 2025

Bauknecht TRK 9876 Útmutató

10 Április 2025

Asko TH208HW Útmutató

10 Április 2025

Zanussi ZTA 245 Útmutató

9 Április 2025

Bauknecht TKL M11 72 Útmutató

9 Április 2025

Amana NGD4600YQ Útmutató

9 Április 2025

Whirlpool awz 9479 Útmutató

9 Április 2025

AEG 65770IH3 Útmutató

7 Április 2025

Arçelik 901 KMP IG Útmutató

7 Április 2025

Arçelik 901 KMP I Útmutató

7 Április 2025