Használati útmutató JL Audio VXi-BTC

JL Audio távirányító VXi-BTC

Olvassa el alább 📖 a magyar nyelvű használati útmutatót JL Audio VXi-BTC (2 oldal) a távirányító kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

FCC Compliance Statement

NOTE: This equipment has been tested and found to comply with the limits of Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

detailed information please visit us online at www.jlaudio.com. Due to our policy of continuous product

development, all specications are subject to change without notice.

VXi-BTC_MAN_050718

Limited Warranty – Electronics (USA)

JL Audio warrants this product to be free of defects in materials and workmanship for a period

of two (2) years from the original date of purchase. This warranty is not transferable and applies

only to the original purchaser from an authorized JL Audio dealer. Should service be necessary

under this warranty for any reason due to manufacturing defect or malfunction, JL Audio will (at

its discretion), repair or replace the defective product with new or remanufactured product at no

charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse,

product modification or neglect, failure to follow installation instructions, unauthorized repair

attempts, misrepresentations by the seller. This warranty does not cover incidental or consequen-

tial damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage

due to accident or normal wear and tear is not covered under warranty.

Warranty is void if the product’s serial number has been removed or defaced.

Any applicable implied warranties are limited in duration to the period of the express warranty

as provided herein beginning with the date of the original purchase at retail, and no warranties,

whether express or implied, shall apply to this product thereafter. Some states do not allow

limitations on implied warranties, therefore these exclusions may not apply to you. This warranty

gives you specific legal rights, and you may also have other rights, which vary from state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL Audio ’s Electronics Service Facility freight-prepaid

through an authorized JL Audio dealer and must be accompanied by proof of purchase (a copy

of the original sales receipt). Direct returns from consumers or non-authorized dealers will be

refused unless specifically authorized by JL Audio with a valid return authorization number.

Warranty expiration on products returned without proof of purchase will be determined from the

manufacturing date code. Coverage may be invalidated as this date is previous to purchase date.

Non-defective items received will be returned freight-collect. Customer is responsible for ship-

ping charges and insurance in sending the product to JL Audio. Freight damage on returns is not

covered under warranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service:

(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc.

10369 North Commerce Pkwy. Miramar, FL 33025

(Do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered

only by that country’s distributor and not by JL Audio, Inc.

JLid™ BLUETOOTH® COMMUNICATOR

Bluetooth® Operation

Multiple devices can be paired to the VXi-BTC, however communication via

Bluetooth® is limited to one active device at a time. The VXi-BTC utilizes a top-

mounted LED control button to manage all pairing and configuration.

Pairing a new device:

1. Connect the VXi-BTC to a JLid™ port of a host device. The LED control

button will initialize, then flash blue.

2. Open and run TüN™ Mobile or TüN™ Express on your mobile device and open the

SELECT/RENAME DEVICE menu. (Opens automatically when app launches.)

3. Select VXi (BT) from the list of available devices, then select . (Select if a OK Pair

Bluetooth Pairing Request prompt appears on your device.) The VXi-BTC LED

ring lights solid blue, then solid green when pairing is successful. Continue

through the TüN™ screen prompts for VXi amplifier configuration.

4. When the SELECT/RENAME DEVICE menu is reopened and Select device

is chosen, the name of the selected BTC host device will be highlighted.

Reconnecting a paired device:

1. Open and run TüN™ Mobile or TüN™ Express on your mobile device and open the

SELECT/RENAME DEVICE menu. (Opens automatically when app launches.)

2. Select VXi (BT) from the list of available devices, then select . The VXi-OK

BTC LED ring lights solid blue, then solid green when pairing is successful.

Continue through the TüN™ screen prompts for VXi amplifier configuration.

Reboot/Restart:

To perform the reboot/restart function, simply cycle the host device’s power or

disconnect and reconnect the VXi-BTC from the JLid™ port of the host device.

Factory Reset:

Performing the Factory Reset function will remove all paired devices from

memory and restore the VXi-BTC to an original, factory default state.

1. Press and hold the LED control button for ten seconds until the LED

ring flashes white once, then release the LED control button.

2. From your device, remove/forget the VXi-BTC from its list of paired devices

before attempting to reconnect/pair the VXi-BTC with the same device.

Note: This step must be performed to avoid an error report in TüN

™.

LED Control Button Status & Functionality

Refer to the table below for the meaning and functionality of the LED control button.

LED

Status

Operational

State Description Note Single Button

Press

Press/Hold

for 10

Seconds

Flashing

Blue

Open

Visibility

VXi-BTC is detect-

able and can be

paired with any

compatible device.

N/A No eect

Initiates

Factory

Reset

(see Factory

Reset

section)

Solid Blue Paired

Indicates a

successful pairing

with a device.

Switches

to Active

Connection

after pairing

Switches to

Open Visibility

state

No eect

Solid

Green

Active

Connection

Indicates a live

connection with a

paired device.

Switches to

Restricted

Visibility when

disconnected

Switches to

Restricted

Visibility state

No eect

Flashing

Green

Restricted

Visibility

VXi-BTC is detect-

able, but can only

be connected to a

previously paired

device.

N/A

Switches to

Open Visibility

state

Initiates

Factory

Reset

(see Factory

Reset

section)

Specifications

Bluetooth® Topology LE (Low Energy)

Bluetooth ®

Core Specication Version 4.2

Host Interface Proprietary VXi JLid™ protocol

Input Operating Voltage 5 VDC

Current Draw 50 mA (max)

Connection Range Up to 33 ft / 10 m

Placement Considerations

The VXi-BTC module should be installed in a location where it can be easily accessed for

device pairing and viewing of its status LED. While the VXi-BTC module can be mounted in

any orientation, its installation location should be considered to optimize RF performance.

For example, we recommend that you avoid mounting it directly to large metal surfaces

or to wire harnesses.

JLid ™

Host Device Connection Options

The VXi-BTC utilizes a proprietary JLid™ protocol for communicating with a host device.

Using the supplied network cable (CAT5e), all energy to power the VXi-BTC is derived

from the JLid™ port of a connected host device. Refer to the chart below for host

device connection options.

JLid™ Host Device JLid™ Host Device Connection Point

VXi Amplier JLid™ CTRL Port or

JLid™

COMM Port

VXi-HUB JLid ™ COMM Accessory Port

Note: If your mounting location exceeds the supplied cable’s length, you may use a

longer cable (not included) of the same type (CAT5e). For optimum performance, the

cable length should be kept as short as possible.

Mounting Clip Installation

A mounting clip is included to secure the VXi-BTC module. Use the supplied

screws to fasten the mounting clip to a flat surface. Once the mounting clip is

installed, attach the VXi-BTC module by pressing one side of its notched center

section against the inside of one of the arms of the mounting clip. Continue

pressing inward until both arms of the mounting clip snap around the notched

center section of the VXi-BTC module. To remove, grasp the body of the VXi-

BTC module and pull while rotating away from the mounting clip.

Product Description

The VXi-BTC is a wireless communication accessory designed to add handheld control

functionality to VXi amplifiers. Equipped with Bluetooth® LE (Low Energy), the

VXi-BTC permits wireless (up to 33 ft/10 m away) configuration of VXi amplifiers

using your compatible mobile device running TüN™ mobile applications. Note: The

VXi-BTC provides a control interface only and does not support audio streaming.

Mobile applications of TüN™ software include:

TüN™ Express – For iPhone, iPad and Android phones and tablets.

Delivers streamlined options, for fast and simple amplifier setup.

TüN™ Mobile – For iPad and Android tablets. Enjoy the full-featured TüN™ software

experience on your tablet, with the freedom of a wireless connection.

(TüN ™

Express and TüN™ Mobile is available on the App Store and on Google Play.)

What is Included

(1) VXi-BTC Bluetooth® Communicator

(1) CAT5e Network Cable (6.5 ft./2 m)

(1) Mounting Clip

(2) Mounting Screws

Termékspecifikációk

Márka:	JL Audio
Kategória:	távirányító
Modell:	VXi-BTC

Szüksége van segítségre?

Ha segítségre van szüksége JL Audio VXi-BTC, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók távirányító JL Audio

JL Audio HD-RLC Útmutató

31 Augusztus 2024

JL Audio MMR-25W Útmutató

29 Augusztus 2024

JL Audio CL-RLC Útmutató

27 Július 2024

JL Audio RBC-1 Útmutató

25 Július 2024

JL Audio VXi-BTC Útmutató

24 Július 2024

JL Audio M-RBC-1 Útmutató

19 Július 2024

JL Audio MMR-10W Útmutató

17 Július 2024

JL Audio MVi-DRCADAPT Útmutató

16 Július 2024

JL Audio DRC-205 Útmutató

12 Július 2024

JL Audio VXi-HUB Útmutató

12 Július 2024

Útmutatók távirányító

Legújabb útmutatók távirányító

Magnum RC-328 Útmutató

9 Április 2025

Conrad src 9200 Útmutató

3 Április 2025

Hama 40095 - 5in1 Útmutató

2 Április 2025

Hama 20312 - Easytip S9 Útmutató

1 Április 2025

Hama 20320 - Zapman 4in1 Útmutató

31 Március 2025

Sonos Controller for iPhone Útmutató

29 Március 2025

Universal Remote Control UR4U Útmutató

29 Március 2025

ELV SRC-7000 Útmutató

27 Március 2025

Metronic ZAP 2 - 495383 Útmutató

27 Március 2025

Metronic 495405z Útmutató

27 Március 2025