Használati útmutató Kicker 50HDS144

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kicker 50HDS144 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 24 ember találta hasznosnak és 9 felhasználó értékelte átlagosan 5.0 csillagra

50HDS144

Motorcycle Audio Kit Installation Guide for Harley Davidson

®

Electra Glide | Street Glide | Ultra Glide | Bat Wing Trikes 2014–

Newer (FLHT)

(1)Wiring Harness

(1)StainlessSteelMountingBracket

(2) PSC652 KickerSpeakers

(4)8-32 NylockNuts

(1)Mounting Hardware

(3)1/4”20 washers

(3)1/4”20 1”bolts

(6)6”BlackCable Ties(1) KPX3004KICKERAmp

(3)1/4”20 NylockNuts

(2) 8”BlackCable Ties

Important:Over-tightening mounting fastenersmayresultin damageto yourmotorcycle.Please referto yourservice manualforproperproceduresand torque

specifications.KICKERisnotresponsible fordamage resulting fromimproperinstallationtechniques.Thiskitmay not becompatiblewithsome aftermarket

head units.

PROGRAMMINGHDRADIO:

NOTE:Itisnecessary tore-flash yourHDradio beforeinstallation ofthiskit.SeeLocal Harley-DavidsonDealerto have HDRadiore-flashed.

1.Removetheseatanddisconnectbothnegative andpositive batteryterminals.

2.Remove the windshield.

3.Remove the outer fairing.

a.Removethefourmountingscrews,unplugtheheadlampandsetaside on asoftcloth.

4.Remove the fueltank.

a.Unplugthefuelfittingontheleftsideofthetank.Youmayremovetheconsoleifyou wanttoretainventlineroutingandconnector

placement.

b.Removeallfourmountingboltsand carefullyliftthetankoffthebikeand setaside.

5.Removewirecaddycover.

a.Carefullyrelease each tabalongthe caddyuntil itlifts completely.

SPEAKER INSTALLATION

6.Remove oneofthe speaker pods from the inner fairing. (Fig.1)

a.There are five fasteners in the center portion and three on the outside to release it from the inner

fairing.

7.Remove the stockspeaker and replace with the PSC652 speaker fromthekit.

a.Install the speaker into the pod and fasten with the original speaker screws. (Fig. 2)

8.Reinstall the pod to the inner fairing.

9.Repeat for the other side.

AMP INSTALLATION

Ifyou have a 2020StreetorTriGlide,the followingstepsmustbecompletedbeforeamplifierinstallation:

Remove four screwsfromtheHDConnect Module. Remove Module fromBracket.Relocate Module to the clutch side ofthe radioand secure withtwo 8” zip tiesincluded.(Fig.

3

and Fig. 4) NOTE: There may be some connectors that will be relocated offof theradio chassisfor theamp bracketto fit.

10. Fasten the amplifier to the bracket with the supplied hardware.

a.Inserttheboltsthroughthebottomofthebracketandinstallthelocknutstotheamplifier.

11.Atthis time,it ishighlyrecommendedtosettheampgain settingto 0.KICKERrecommendsthatthedip switchesbe setup asfollows(Fig. 5)

InputGaincontrol– 0

Autoturn-on- 12V

Fader- ON

Inputlevel - HI

Amp1:HI-PASS – 80 Hz

Amp2:HI-PASS – 60 Hz(6x9)

80 Hz(6.5”TourPack)

12.AfterfinishingSystemSetup,usethe supplied¼”hardwareandfastentheamp/bracketassemblytotheradiochassiswiththe10-pinconnectorandpowerconnector

facing the throttle side. (Fig. 6)

HARNESSINSTALLATION

13.Plug the harness into the amplifier and route the speaker wires to their respective locations. (Fig. 7)

a.Separate the speaker connectors and plug in the amplifier harness to each speaker.

14.Plug the4-pin male, rear audio connector into the 4-pin female rearaudio signal connector coming from the radio harness. (Fig. 8andFig. 9)

15.Plug the switched power harness into the 2-pin amp connector on the throttle side of the fairing. (Fig. 10)

16.Plug the blue wire on the kicker harness into the switched power harness lead with one wire.

a.This allows for an accessory 12V port to remain available.

17.Route the power leads and the rear speaker plugalong the clutch side ofthe frame neck,in the electrical caddyto the seatarea.(Fig.11)

18.Reconnectthe batteryterminalsand pullthe excessharness slack back into the fairing. Create a slack loop with excess harness slack.

19.Plug the radio in andsetthegain. If not using rear speakers it is recommend to leave the amp 2 gain turned all the way down.

20.Testcomponentfunctionand setthe gain to optimizesystemperformance.

21.Carefullyreassemble themotorcycle and enjoyyournewaudio kit!

Note: If you are not using rear speakers you will need to connect the Dummy Plug (fig. 13) to the rear speaker connector under the seat.

Forquestions,please contactKICKERTechnical Supportat800-256-0808,M-F 8:00 am– 5:00 pmCSToremailatsupport@kicker.com

Torx T-27

Package Contents:

(1)InstallGuide

(4)8-32 x1/2”Button HeadBolts

Tools Needed: 3/16" Allen wrench

10mm Box end wrench

7/16" Box end wrench or socket

Torx T-40

Note: At this time it is highly recommended to cover the dip swtiches with the included mylar cover as seen in (Fig. 12)

(1)Mylar cover

(1) Dummy Plug

Termékspecifikációk