Használati útmutató King LPWA2445-TP-W
Olvassa el alább 📖 a magyar nyelvű használati útmutatót King LPWA2445-TP-W (2 oldal) a Fűtő kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 7.5 felhasználó értékelte átlagosan 4.3 csillagra
Oldal 1/2
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS
OWNERS GUIDE & INSTALLATION INSTRUCTIONS SHOULD BE LEFT WITH HEATER FOR HOME OWNER
KING ELECTRICAL MFG. COMPANY • 9131 10th Ave So. • Seattle, WA 98108 • Ph: 206.762.0400 • Fax: 206.763.7738 • www.king-electric.com
It is recommended to order your unit with or without the thermostat for your particular application. If your unit has ALWAYS
been ordered incorrectly please contact the factory and we can exchange it for the proper unit. Adding a built-in thermostat
after installation is complicated and could result in creating wiring errors and shorting out the unit.
Instructions for wall mount heater with built-in thermostat
It is to verify the electrical power supply is the same voltage as the heater you are installing. extremely important 208, 240,
277 and 120 Volt heaters are not interchangeable. Powering a 208, 240 or 277 Volt unit with 120 Volt supply wires will
reduce the heater's output by approximately 75%. Powering a 120 Volt unit with 208, 240 or 277 Volt supply wires will destroy
the heater and voids all warranties.
NOTICE must: For heaters without built-in thermostats, using remote or wall-mounted thermostats: the power be brought to
the heater rst (not to the wall-mounted or remote thermostat). This is necessary to provide power for the fan to cool down the
element after the thermostat has opened. Use only a single pole line voltage wall thermostat or switch to control this heater.
CAUTION: Open the circuit breaker supplying the heater before attempting installation, maintenance, or repairs. Lock
or tag circuit breaker panel door. Failure to do so could result in serious electrical shock, burns, or possible death.
1. Remove heater contents from carton and check for shipping damage.
2. Remove grille by loosening the four mounting screws along the sides
of the front panel.
3. Detach interior assembly from the wall can by removing the four
screws along each side of the interior panel. Lift and tilt assembly
away from the top of the wall can. Free the bottom edge from the
metal lip inside the wall can. Place the interior assembly in a safe
location until the wall can is mounted.
4. Remove one knockout from the wall can and thread supply wires
through the hole. Use an approved cable connector to prevent wires
from chang. Connect groundwire to green pigtail.
5. Mount heater wall can on wall studs a minimum of 6" from side wall
and 4" from oor, using the holes provided in the sides of the box.
The face of the box should be ush with the nished wall. Installation
of the interior and grille to the wallbox cover an approximate 5/8"
periphery along the outer area of the opening.
6. After wall can is secured interior assembly leads may be attached
to supply wires and interior secured to wall can. The LPW NOTE:
wall heater is equipped with two steel elements having a capacity of
2250 Watts each, for a combined capacity of 4500 Watts. The heater is factory-
wired at 4500 Watts. To adjust the heater for lower wattages remove the appropri
ate colored wire according to the illustration and wattage diagram provided on the
back side of this sheet. Be sure to insulate and secure the unused lead.
7. Reinstall interior assembly on wallbox using screws provided.
8. Mount grille to interior with screws provided.
9. Installation is now complete and the heater ready for use.
LPW2045T, LPWA2045T, LPW2445T, LPWA2445T, LPW2740T, LPWA2740T
240 VOLT MODELS with Disconnect Breaker and Remote User Switch
Maintenance & Warranty
The high quality and superior design of this unit will enable years of maintenance free performance. Once yearly
the heater should be checked for lint or dust accumulation but no further maintenance is required. The motor is
permanently lubricated and sealed. A 5-year warranty is provided on the Pic-A-Watt ® element and 1-year on all
materials, components and workmanship.
VISUAL ALARM
This heater includes a visual alarm to warn that
parts of the heater are getting excessively hot.
If the alarm ashes, immediately turn the heater
o and inspect for any objects on or adjacent to
the heater that may cause high temperatures.
Do not operate the heater with the alarm
ashing.
LPW-As with disconnect.indd : 8/09
FAN-FORCED HEATERS:
Clearances for Safe
Operation
Termékspecifikációk
| Márka: | King |
| Kategória: | Fűtő |
| Modell: | LPWA2445-TP-W |
Szüksége van segítségre?
Ha segítségre van szüksége King LPWA2445-TP-W, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Fűtő King
15 Március 2025
3 Szeptember 2024
3 Szeptember 2024
2 Szeptember 2024
29 Augusztus 2024
28 Augusztus 2024
21 Augusztus 2024
21 Augusztus 2024
15 Augusztus 2024
12 Augusztus 2024
Útmutatók Fűtő
- Fűtő Eldom
- Fűtő Omega Altise
- Fűtő Eden
- Fűtő Thomson
- Fűtő Orbegozo
- Fűtő Euromac
- Fűtő Nevir
- Fűtő ECG
- Fűtő Extraflame
- Fűtő TANSUN
- Fűtő Becken
- Fűtő Heat1
- Fűtő Bimar
- Fűtő Thermotec
- Fűtő CaterChef
Legújabb útmutatók Fűtő
6 Április 2025
4 Április 2025
30 Március 2025
30 Március 2025
30 Március 2025
30 Március 2025
27 Március 2025
27 Március 2025
27 Március 2025
27 Március 2025