Használati útmutató Lanzar OPTIX5

Lanzar nincs kategorizálva OPTIX5

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Lanzar OPTIX5 (8 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
- 1 -
FRONT AND REAR CHANNEL : SUBWOOFER CHANNEL:
* High Pass Frequency Selector * Subwoofer Input Switch
40Hz to 400Hz / 32Hz to 250Hz * +12dB Bass Boost
* Frequencies Multiplier p2-x1 or x20 * Phase Shift Switch
* Crossover Slope 6dB/Octave or * Stereo/Mono Switch
12dB/Octave * Output Level Control
* Signal Gain Control * Exclusive Remote Subwoofer Level Control
* Parallel Input Switch * Low Pass Frequency Selector 40Hz to 400Hz
* Bass Boost Frequency Selector 25Hz to 250Hz
Power Supply....................................... DC to DC switching power
S/N Ratio............................................. 110dB
Channel Separation.............................. 80dB
Distortion.............................................. THD @ 0.01%
Crossover Slope.................................... 12dB per Octave
Input Impedance................................... 20K Ohms
Output Impedance................................ 100 Ohms
Output Gain.......................................... 1:2 (+6dB)
Output Voltage Level........................... 8Volts Max
Dimensions.......................................... 5-13/16" (W) x 8-1/4" (L) x 1-3/8" (H)
1. Find a suitable location in the vehicle to mount the crossover.
2. Bolt the crossover to the mounting surface.
3. Using the screw terminals provided, connect minimum 16 gauge wire from the power,
Ground and remote terminals. Connect the shortest possible wire to a chassis ground point. The (+)
12V connection should be made directly to the car battery, and the remote should be connected to
the Remote Turn On Lead of your head unit. When connecting directly to the battery, install a 3A
Fuse within 18 inches of the battery terminal.
4. Connect all line inputs and outputs using high-quality RCA cables.
5. Recheck all connections before powering up.
6. Set all level controls to their minimum positions and set all crossover controls, switches, etc. To
the desired frequency or position.
7. Once the system is powered up, set the volume control on the head unit to a moderate level where
your normal speaking voice can be heard while the music is playing.
8. Further fine tuning of the various controls may be necessary to obtain the desired results.
9. When unsure about installation or system tuning, please consult an authorized dealer.LANZAR
INSTALLATION
FEATURES
SPECIFICATIONS
Features and specifications subject to change without notice.
Congratulations on your purchase of a Crossover. This product has been designed LANZAR
and built to deliver excellent sound quality and long lasting high performance. We are sure you
will enjoy listening to your favorite music with this component in your car audio System. LANZAR
For best result a professional car stereo installer for application advice or troubleshooting. Thank
you for choosing products for your auto-sound system. Everything else is just noise LANZAR
INTRODUCTION
- 2 -
CONTROLS AND OPERATION
1. Ground Terminal (GND).
2. Remote Turn-On Terminal (REM).
3. Power Terminal (+12V).
4. Power Indicator.
5. Front Channel Inputs.
6. Parallel Input Switch: If there are 4 sets (2 pairs/ Front & Rear) RCA inputs available, place
this switch in the "IN" position. If there is only one pair of input RCA connectors being used,
place this switch in the "OUT" position to provide Front and Rear input from that single pair of
RCA inputs.
(Note that the Front inputs are essentially the main inputs, thus providing an input to
these terminals, and properly selection of the various switch positions would provide
signals on ALL of the various outputs.)
7. Rear Channel Inputs.
8. Subwoofer Channel Inputs.
9. Subwoofer Input Switch: If there is no dedicated subwoofer signal available from the signal
source, place this switch in the "ON" position to provide signal at the subwoofer output terminals.
If there is a dedicated subwoofer signal source available for this input purpose, place the switch
in the "OFF" position.

Termékspecifikációk

Márka: Lanzar
Kategória: nincs kategorizálva
Modell: OPTIX5

Szüksége van segítségre?

Ha segítségre van szüksége Lanzar OPTIX5, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Lanzar

Lanzar

Lanzar VCAP1200 Útmutató

15 Augusztus 2024
Lanzar

Lanzar VCAP8000 Útmutató

13 Augusztus 2024
Lanzar

Lanzar VCAP3000 Útmutató

12 Augusztus 2024
Lanzar

Lanzar VCAP5000 Útmutató

11 Augusztus 2024
Lanzar

Lanzar OPTICAP300 Útmutató

10 Augusztus 2024
Lanzar

Lanzar OPTIX5 Útmutató

9 Augusztus 2024
Lanzar

Lanzar OptiX-6 Útmutató

8 Augusztus 2024
Lanzar

Lanzar VCAP10000 Útmutató

8 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025