Használati útmutató M-Audio CT-14

Olvassa el alább 📖 a magyar nyelvű használati útmutatót M-Audio CT-14 (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
CT-14
1x4 Digital Audio
Coaxial S/PDIF
Thru Box
CT-14
MANUAL
CT-14
1x4 Digital Audio Coaxial S/PDIF Thru Box
Thank you for purchasing the CT-14, by M Audio. The CT-
14 accepts one S/PDIF digital audio signal via coaxial RCA
connector and duplicates it to four S/PDIF coaxial RCA
outputs, all on the rear of the CT-14. This allows you to
take the S/PDIF output of any digital audio source, such
as a DAT, CD player, digital mixer, etc., and send it
simultaneously to four digital audio targets that are
capable of receiving S/PDIF format signals. The CT-14
will flawlessly pass any coaxial S/PDIF signal having
100kHz or less sample rate and any data width. Its
active electronics assure that the integrity of your digital
signal is never compromised.
The setup example that follows shows what might be a
typical mixing scenario. The output of a digital mixer is
connected to the CT-14 input, while a DAT, computer-
based digital audio card (such as an M Audio “Delta DiO
2496 or DiO 2448), a CD recorder, and a D/A
Converter (to feed your monitors) are connected to the
CT-14 outputs. This setup allows the user to take one
mix output and simultaneously record to several mixdown
decks, saving hours of time and possible frustration.
To set up the CT-14 in your system, first make sure all of
your external devices are turned off. Then, using good-
quality 75-ohm coaxial digital cables with male connectors
(digital video cables meet this requirement) for best
results, follow this simple procedure:
TM
1. With the CT-14 power button in the out (off) position, plug the
appropriate end of the supplied 9-Volt DC wall-wart power
adapter into your CT-14 and the other end into a wall socket or
power strip. The CT-14 power indicator LED should be off.
2. Take the output of your digital audio source device and plug it into
the CT-14 coaxial RCA input connector located on the rear of the
CT-14 .
3. Connect the CT-14s coaxial RCA digital output connectors to the
inputs of your receiving or target digital audio devices. You may
want to connect the analog audio output of one of these target
devices to a sound system for monitoring purposes.
4. With all volumes turned down, turn on your source device.
5. Turn on the CT-14 by pressing its power button and allowing it to
latch in the in position. The power indicator LED will light on the
front of the CT-14 unit.
6. Turn on your target devices. Your CT-14 is now ready for use.
CT-14
Hook-Up
Diagram

Termékspecifikációk

Márka: M-Audio
Kategória: nincs kategorizálva
Modell: CT-14

Szüksége van segítségre?

Ha segítségre van szüksége M-Audio CT-14, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva M-Audio

M-Audio

M-Audio CO2 Útmutató

7 Szeptember 2024
M-Audio

M-Audio SBX10 Útmutató

14 Augusztus 2024
M-Audio

M-Audio UC-33e= Útmutató

14 Augusztus 2024
M-Audio

M-Audio MidAir Útmutató

13 Augusztus 2024
M-Audio

M-Audio Delta 44 Útmutató

13 Augusztus 2024
M-Audio

M-Audio Solaris Útmutató

13 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025