Használati útmutató Makita JN1601

Makita vágógép JN1601

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Makita JN1601 (8 oldal) a vágógép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
IMPORTANT: Read Before Using.
Nibbler
JN1601
004772
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model JN1601
Steel up to 400 N/mm2 1.6 mm / 16 ga
Steel up to 600 N/mm2 1.2 mm / 18 ga
Steel up to 800 N/mm2 0.8 mm / 22 ga
Max. cutting capacities
Aluminum up to 200 N/mm
2 2.5 mm / 13 ga
Outside edge 50 mm
Min. cutting radius Inside edge 45 mm
Strokes per minute (min-1
) 2,200
Overall length 261 mm
Net weight 1.6 kg
Safety class /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･ DOUBLE INSULATION
･ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible recycling
facility.
ENE037-1
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA) : 83 dB(A)
Sound power level (L
WA) : 94 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode : cutting sheet metal
Vibration emission (ah) : 7.0 m/s2
Uncertainty (K) : 1.5 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
3
ENH101-15
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Nibbler
Model No./ Type: JN1601
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
30.1.2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
GEA005-3
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control

Termékspecifikációk

Márka: Makita
Kategória: vágógép
Modell: JN1601

Szüksége van segítségre?

Ha segítségre van szüksége Makita JN1601, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók vágógép Makita

Makita

Makita CC300DZ Útmutató

2 Szeptember 2024
Makita

Makita WST05 Útmutató

17 Augusztus 2024
Makita

Makita EBH252U Útmutató

2 Augusztus 2024
Makita

Makita JN1601 Útmutató

26 Július 2024
Makita

Makita CP100DZ Útmutató

24 Július 2024
Makita

Makita JN1601J Útmutató

17 Július 2024
Makita

Makita BTM50Z Útmutató

16 Július 2024
Makita

Makita CC300DWE Útmutató

13 Július 2024
Makita

Makita DJS200Z Útmutató

10 Július 2024
Makita

Makita DEAWST06 Útmutató

14 Június 2024

Útmutatók vágógép

Legújabb útmutatók vágógép

Logan

Logan 350-1 Útmutató

27 Március 2025
Logan

Logan Artist Elite 450-1 Útmutató

27 Március 2025
Genius

Genius Nicer Dicer Quick Útmutató

12 Január 2025
Eldom

Eldom Sliss KR350 Útmutató

11 Január 2025
RGV

RGV Desy AF 220 AM Útmutató

11 Január 2025
RGV

RGV Desy AF 275 F Útmutató

11 Január 2025
Ovela

Ovela OVSAFSLCERA Útmutató

6 Január 2025
Royal Catering

Royal Catering RCAM-250 Útmutató

4 Január 2025
Royal Catering

Royal Catering RCES-215/12 Útmutató

1 Január 2025
CaterChef

CaterChef 537150 Útmutató

1 Január 2025